IHP Superior Fireplaces F3412 Скачать руководство пользователя

Страница: 14 / 32

SuperiorFireplaces.us.com

900855-00_C

VENTING INSTALLATION

Continued

Terminations/Spark Arrestor

The fireplace system must be terminated with the listed round top or

chase terminations. In any case, refer to the installation instructions

supplied with the termination.

CAUTION: Do not seal openings on the rooftop

flashing. Follow the installation instructions provided

with the termination being used.

Figure 21 - Multiple Chase Installation

Figure 22 - 10 Foot Rule

Figure 20 - Termination

RLT-12D

Level of Flue

Gas Outlet

Stainless

Inner Flue

Pipe

Waterproof

Caulking

Storm

Collar

Flashing

Underlap

Shingles

Overlap Shingles

(Top and Sides of

Flashing Base)

Secure

Termination

to Outer

Pipe with 3

Screws

CHASE INSTALLATIONS

Instructions for chase installations are included with the chase style

termination chosen. In a multiple chase installation, be sure to provide

adequate distance between terminations to prevent smoke spillage

from one termination to another. We suggest that terminations be

separated at least 24", center to center and stacked at a vertical height

difference of 18" (see Figure 21).

Note:

If a decorative shroud is to be installed, contact the manufac-

turer for specifications.

10 FOOT RULE

All flue gas outlet chimney terminations must extend a minimum of

3 feet in height above the highest point where it passes through the

roof and must be at least 2 feet above the highest point of the roof

that is within a horizontal distance of 10 feet (see Figure 22).

(3.05 m)

(0.61 m) Min.

(0.61 m)

Min.

(0.91 m)

Min

(0.91 m)

Min

Level of Flue

Gas Outlet

24" (610 mm)

18" (458 mm)

Min. Typ.

24" (610 mm)

SQUARE TOP TERMINATIONS INSTALLATION STL-12D AND

STL-12DMP

1. Construct chase as illustrated in Figure 23.

Note:

The shortest

vertical side must be at least 30" high and minimum inside di-

mension must be at least 19" as shown in Figure 23.

2. Add pipe sections to chimney system as outlined in fireplace

installation instructions until last piece of chimney is a maximum

of 6" below top of chase (see Figure 23).

Figure 23 - Constructing Chase

19"

(483 mm)

6" (153 mm) Max.

30"

(762 mm)

Min.

Содержание Superior Fireplaces F3412

































Результаты поиска

Содержание Superior Fireplaces F3412

Отзывы:

Похожие инструкции для Superior Fireplaces F3412

Бренды по названию

Популярные бренды

IHP Superior Fireplaces F3412, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Superior Fireplaces F3412

Отзывы:

Похожие инструкции для Superior Fireplaces F3412

Бренды по названию

Популярные бренды