IHP Superior Fireplaces F3412 Скачать руководство пользователя

Страница: 7 / 32

SuperiorFireplaces.us.com

900855-00_C

FIREPLACE INSTALLATION

SELECTING LOCATION

To determine the safest and most efficient location for the fireplace,

you must take into consideration the following guidelines:
1. The location must allow for proper clearances (see Figures 4 thru

7).

2. Consider a location where fireplace will not be affected by drafts,

air conditioning ducts, windows or doors.

3. A location that avoids cutting of joists or roof rafters will make

installation easier.

4. An outside air kit is available with this fireplace (see Optional

Outside Air Kit on page 10).

MINIMUM CLEARANCE TO COMBUSTIBLES

Back and sides of fireplace

1" (26 mm) min.

Ceiling

42" (1067 mm) min.

Front of fireplace

48" (1220 mm) min.

Floor**

0" (0 mm) min.

Perpendicular wall to opening

12" (305 mm) min.

Top spacers

0" (0 mm) min.

Mantel clearances

see Mantels, page 9

Chimney outer pipe surface

1" (26 mm) min.

* Not required at nailing flanges

** See step 2 of Framing

WARNING: Do not pack required air spaces with

insulation or other materials.

Minimum/Maximum Chimney Height for Residential Installation

Minimum height of chimney, measured from base of fireplace to flue

gas outlet of termination, is 16 feet for straight flue or a flue with one

elbow set. Maximum distance between elbows is 6 feet. For systems

with two elbow sets, minimum height is 22 feet. Maximum height of

any system is 50 feet. This measurement includes fireplace, chimney

sections and height of termination assembly at level of the flue gas

outlet (see Figure 17, page 13).

FRAMING

1. Frame opening for fireplace using dimensions shown in Figures 4

and 5.

2. If fireplace is to be installed directly on carpeting, tile or any

combustible material other than wood flooring, fireplace must

be installed upon a metal or wood panel extending full width and

depth of fireplace.

3. Set fireplace directly in front of this opening and slide unit back

until nailing flanges touch side framing.

4. Check level of the fireplace and shim with sheet metal if necessary.
5. Before securing fireplace to prepared framing, ember protector

(provided) must be placed between hearth extension (not sup-

plied) and under bottom front edge of fireplace to protect against

glowing embers falling through. If fireplace is to be installed on a

raised platform, a Z-type ember protector (not supplied) must be

fabricated to fit your required platform height. Ember protector

should extend under fireplace a minimum of 1

". Ember protector

should be made of galvanized sheet metal (28 gauge minimum to

prevent corrosion.

6. Using screws or nails, secure fireplace to framing through flanges

located on sides of fireplace.

Содержание Superior Fireplaces F3412

































Результаты поиска

Содержание Superior Fireplaces F3412

Отзывы:

Похожие инструкции для Superior Fireplaces F3412

Бренды по названию

Популярные бренды

IHP Superior Fireplaces F3412, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Superior Fireplaces F3412

Отзывы:

Похожие инструкции для Superior Fireplaces F3412

Бренды по названию

Популярные бренды