NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
6
Figure 4
Figure 5
NEW CONSTRUCTION OR RENOVATION
1. Select a location that is not prone to moisture
and is located at least 3 feet (or 0.9m) away
from combustible materials such as curtains
or drapes, furniture, bedding, paper, etc.
2. Place the unit in selected location to see how
it will look in the future.
3. Mark the desired location on the fl oor and
store unit in a safe, dry and dust free location.
4. Frame in an opening leaving at least 1/4"
(6mm) around the edge of the unit. Any
new wiring must be done in compliance with
local and national codes and other applicable
regulations in order to reduce the risk of fi re,
electric shock or other injuries. Therefore,
it is strongly recommended that you hire a
professional to complete any such work.
INSTALLING THE FIREPLACE INSERT
1. Once the site has been prepared, the fi replace
insert can be installed.
2. Make sure the switch is in the "OFF" position.
3. Plug the fi replace into a 15-amp/120 volt,
grounded outlet.
4. Push the fi replace insert so that the trim is
against the fi nished mantel or wall surface.
WARNING
GRILLS ON THIS ELECTRIC FIRE-
PLACE CANNOT, IN ANY WAY, BE
COVERED AS IT MAY CREATE A
FIRE HAZARD.
NOTE:
Power supply service must be complete
prior to fi nishing, to avoid reconstruction.
Grills and air openings
cannot
be covered in
any circumstances.
OPERATING INSTRUCTIONS
1. Plug in your electric fi replace.
2.
Main ON/OFF Power switch:
This switch
is located on the right side of the control
panel
(see
Figure 4
)
. When the unit is on,
the default settings for the fi replace is HI
ember bed and fl ame and the heater is OFF.
3.
Temperature Control button and LED:
This
button is located to the left of the Remote
Control Receiver
(see
Figure 4
)
. The LED
is located to the left of the Flame Button.
Push button to cycle through the settings.
When this button is pushed, the LED will
change to its corresponding color; Green
for LO, Orange for MED, and Red for HI.
When heater is on, heat will emit through
vents located above the fi rebox opening
panel
(see
Figure 6, Page 7
)
.
Flame Control
Button
ON/OFF Power
Button
Temperature
LED
Temperature
Control Button
Remote Control
Receiver
FL TM
The heater has a built in thermostat so it will shut
off automatically once the set temperature is
reached. It will also turn on automatically if
the room temperature drops below the set
temperature.
NOTE:
When the heater is turned on for the
fi rst time, it may release a slight, harmless odor.
This odor is a normal occurrence caused by the
initial heating of the internal heating elements
and should not occur again.
4.
Flame Control button:
This button is located
to the left of the Temperature Button
(see
Figure 4
)
. After power is on, push the
Flame Control Button to adjust fl ame and
ember bed brightness. Press and release
the Flame Control Button to cycle through
LO, MED, HI and OFF.
OPERATING BY REMOTE CONTROL
(see
Figure 5
)
1. To control the electric fi replace by remote
control, the main power on/off switch
should be in the off position. This switch is
located on the front left fl oor of fi rebox (see
Figures 4 & 5
).
2. When operating the remote control, it must
be pointed at the logs inside the electric
fi replace and a beep must be heard each time
you press a function button. The beep lets
you know the remote control is operating the
function button you are pressing.
3. Remote On/Off Button - The button on the
top left (see A) is the on/off power button.
When pressing this button you will hear
a beep, this will activate the power to the
fi replace. You must then press the display
button (C) to activate the lights.
4. To increase the brightness, press and release
the light brighten button (see E). Each time
you press this button you will hear a beep,
and the brightness will increase slightly until
the maximum brightness is achieved. To
decrease the brightness, press and release
the light dimming button (see D). Each time
you press this button you will hear a beep,
and the brightness will decrease slightly
until the minimum brightness is achieved.
5. Heater Button - Press this button and the
heater will operate at 1900W (F). If pressed
again, the heater will turn off.
6. Temp - Press this button (I) to automatically
control room temperature.
HIGH (H), or LO (G). The heater is preset
to the following temperatures:
• HIGH heater works at 1900W
• LO heater works at 950W6.
7. If a yellow fl ame is desired, press and
release the (K) button until the desired fl ame
color is reached. Each time the button is
depressed, you will hear a beep and the
fl ame will change from blue to yellow until
the maximum setting is reached. If a blue
fl ame is desired, press and release the (J)
button until the desired color is reached.
7. To turn the electric fi replace off, Press the On/
Off button once (A), when you hear the beep
the fi replace will be completely off. When you
restart your fi replace with the remote control,
all settings will restart at the high settings pro-
grammed at the factory. You may also simply
press the (C) button to turn off the fl ame and
still use the heater.
NOTE:
Make sure your batteries are fully charged
and installed correctly in your remote control.
A
D
F
H
G
J
C
B
E
I
K
Содержание capella 27
Страница 10: ...10 NOTES...
