NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
WARNING
ALWAYS DISCONNECT POWER
AND ALLOW THE ELECTRIC
FIREPLACE TO COOL BEFORE
PERFORMING ANY CLEANING,
MAINTENANCE OR RELOCATION
OF THIS ELECTRIC FIREPLACE.
TURN CONTROLS TO OFF AND
REMOVE PLUG FROM OUTLET OR
TURN OFF CIRCUIT BREAKER TO
ELECTRIC FIREPLACE.
BACK GLASS
1. The glass is cleaned in the factory during
assembly. During shipment, installation,
handling, etc.. The glass surface may col-
lect dust particles. These can be removed
by buffi ng lightly with a clean dry cloth. To
access the back glass, refer to
Figure 6
and
the removal process in the next section.
2. To remove fi ngerprints or other marks, the
glass can be cleaned with a damp cloth using
a good quality household glass cleaner. The
glass should be completely dried with a lint
free cloth or paper towel.
3. In the event of glass breakage, vacuum all
remaining glass pieces with a shop vac.
DO
NOT VACUUM WHILE PIECES ARE HOT!
Replace glass only with replacement parts
specifi cally for this heater. Never substitute
material. Only fully tempered safety glass
may be used on this heater.
b. Flame Cylinder LED Strip
i. Remove Mirror panel, following proce-
dure on Page 8 (see
Brick panel Removal
Procedure
).
iii. Locate fl ame cylinder drum (see
Figure
17
).
Locate the cotter pin on left side of
fl ame cylinder and remove it. Remove
outer plastic sleeve of drum by remov-
ing the (3) screws on the right side of
the sleeve. Disconnect the left side
of the fl ame cylinder drum from the
motor, and slide the outer sleeve off.
you will have access to the LED strip
(see
Figure 18
).
Note:
do not exert
excessive pressure on the drum
cylinder as this may cause damage.
v. Using needle-nose pliers, squeeze the
plastic clips holding the LED strips in
place and push them through the holes
in the LED strip. Unclip the wires from
the LED strip and remove it.
6. Reinstall all components that were removed
(reverse
Steps 1-5
)
.
Access LED strips as follows:
a. Ember Bed LED Strips-
i. With the ember bed removed, the 2
ember bed LED strips will be visible (see
Figure 13
).
ii. Using needle-nose pliers, squeeze the
plastic clips holding the LED strips in
place and push them through the holes
in the LED strips (see
Figure 14
). Unclip
the wires from the LED strips and remove
them. Insert new LED strips and re-
connect the associated wiring.
iii. Plug in power cord or connect power to
appliance. Turn on power to test LEDs.
Disconnect power.
iv. Reverse
Steps 3 to 5
.
ii. using a phillips screwdriver, remove the
fl ame panel (see
Figure 16
)
.
Figure 12
Mirror Glass Panel
Mirror Glass Panel
Figure 13
LED Strips
LED Strips
Plastic Retaining Clips
Plastic Retaining Clips
Figure 14
Figure 15
M i r r o r e d G l a s s
M i r r o r e d G l a s s
Retaining Brackets
Retaining Brackets
Grate
Grate
Log/Ember Assembly
Log/Ember Assembly
Figure 16
Figure 17
Figure 18
Flame
Flame
Panel
Panel
Flame Cylinder Drum
Flame Cylinder Drum
LED Strip
Cotter Pin
Cotter Pin
Flame Cylinder
Cover
(3) Screws
(3) Screws
LED Strip Replacement Procedure:
• 2 LED strips provide illumination for the
ember bed and 1 LED strip provides illumina-
tion for the fl ame generation assembly.
• Replacement LED strips are available through
IHP (see
Page 16
).
1. Turn off power to the fi replace.
2. Let the fi replace cool, if it has been operat-
ing.
3. (If optional glass panel enclosure is
installed) Remove glass panel per instruc-
tions provided in kit.
4. Remove the 2 screws on the front of the
grate (see
Figure 12
. Also see item #7 on
Page 17
). Remove Grate.
5. Lift out log/ember assembly by tilting for-
ward and fi rmly pulling on back of ember
bed assembly. It should pop out from
track and lift out. Caution: Be careful not
to scratch the fi nish.
Screws
Screws
Содержание capella 27
Страница 10: ...10 NOTES...
