NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
5
INNOVATIVE HEARTH PRODUCTS
•
LINEAR ELECTRIC FIREPLACE
•
INSTALLATION INSTRUCTIONS
MINIMUM CLEARANCES TO COMBUS-
TIBLES
Mantel Clearance:
Combustible and Non-
combustible mantels may be installed above
the top of the face of fireplace.
54" Models: ERC4054, Arturcus54, and
MPE54L
Description: 54" Linear Electric Fireplace
Shipping Weight: 70 1/2 lbs. (32 KG)
Packaging:
57” x 6 1/2” x 22 3/8”
(1448mm x 165mm x 568mm)
4.94 cu. ft.
Power Requirements:
(120 Volt, 60 Hz.)
Rated Wattage - 1600 Watts
Amperage - 13.33 Amps
Blower CFM: 83 CFM
(120 V): 5,461 BTU/HR
FIREPLACE SPECIFICATIONS
This appliance is an electric fireplace designed
to be framed in with combustible materials (up
to the edge of the appliance).
When surface mounting the fireplace with
the heater function enabled, a shelf must be
a minimum of 15 3/4" above the discharge of
the heater.
WARNING
Do not use this fireplace if any
part of it has been underwater.
Immediately call a qualified
service technician to inspect the
fireplace and replace any part of
the electrical system which has
been under water.
PRE-INSTALLATION
Before You Start
Check appliance for any concealed damage.
DETAILED INSTALLATION STEPS
WALL MOUNTING
1. Do not connect the appliance until properly
fixed to the wall and the instruction manual
is read fully.
2. Two people are recommended for installation
of this electric fireplace heater.
3. Peel off the removable label and the pro-
tective sheet attached to the front tempered
glass.
4. To place the decorative crystals media
follow the steps as given below
a. To place the crystals, the front glass is
required to be removed from the heater panel
body. Unscrew top and side screws which
hold the glass as shown in
Figure 4a and 4b
.
60" Models:
ERC4060, Arturcus60, and
MPE60L
Description: 60" Linear Electric Fireplace
Shipping Weight: 72 3/4 lbs. (33 KG)
Packaging:
62 3/8” x 6 1/2” x 22 3/8”
(1584mm x 165mm x 568mm)
5.3 cu. ft.
Power Requirements:
(120 Volt, 60 Hz.)
Rated Wattage - 1600 Watts
Amperage - 13.33 Amps
Blower CFM: 83 CFM
(120 V): 5,461 BTU/HR
b. Once the screws are out the top metal
bracket will come loose, place the bracket
away. Make sure the glass is supported
while doing this. Lift the glass up and out
from the heater body.
c. Place the crystals along the light unit in
desired position.
d. Put the front glass back and place the
metal bracket on top of the glass so that
the bracket secures it. Put the fasten screws
back. Make sure the screws are tight and
the glass is secured before continuing with
the installation.
5. A minimum recommended viewing distance
of 15" is recomended.
6. For installation of the appliance, care must
be taken not to damage concealed cables.
Please be careful while drilling the holes.
7. This appliance is designed to be permanently
fixed to a wall at a minimum height of 7 7/8"
(300mm). The wall bracket must be
fitted horizontally and the cable routed to
the bot tom right of the heater.
8. A minimum height of 15" from bottom of
heater to floor is recommended for optimum
viewing of fuel bed. See the
Figure 2
for the
recommended framing dimensions.
10. Carefully lift the heater up ensuring that
the top rear edge of heater engages the wall
bracket and is sit ting centrally. Two people
will make this operation easier.
11. Gently bring the heater level with the wall
and hang the heater to the heater bracket.
Ensure the heater body is locked in with the
wall bracket.
12. Attach the bottom bracket to the heater
panel body and mark the mounting hole;
remove the heater.
13. Drill the bracket mounting hole and fit the
wall plug.
14. Refit the heater to the wall and secure the
bottom bracket using the screws provided
to permanently fix the heater in place.
Ensure the heater body is engaged with the
wall bracket at the top. The heater is now
ready for use.
Figure 4a
Figure 4b
WARNING
The minimum recommended
safe distance from the fireplace
to adjacent walls and furnishings
is 15 3/4" (600mm).
Fireplace Clearances
WALL
RECESS
Sides
7 7/8"
(300mm)
0" (0mm)
Floor
7 7/8"
(300mm)
0" (0mm)
Top
15 3/4"
(600mm)
0" (0mm)
Rear
0" (0mm)
0" (0mm)
Table 2
900264-00 Rev. NC 06/14
