NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
8
8
INNOVATIVE HEARTH PRODUCTS
•
LINEAR ELECTRIC FIREPLACE
•
INSTALLATION INSTRUCTIONS
•
When using the
remote control
, the
power
on/off switch
on the lower right side of the
unit must be in the "ON" position.
REMOTE CONTROL OPERATION:
Figure 9
Theis IHP Electric Fireplace is provided
with an Infrared light Remote Control.
All functions of the fireplace can be con-
trolled through the remote control. Note:
The Effective range of the remote control
is up to approximately 26 feet (8 meters).
The functions identified on the remote (see
Figure 9
)
are as follows:
A. POWER BUTTON
Press once to turn on power to fireplace.
B. INDICATING LIGHT
Illuminates when signal is sent.
C. FLAME BUTTON
On/off switch for flame and ember light.
D. AMBER FLAME BUTTON (DIM)
Reduces brightness of amber light.
E. AMBER FLAME BUTTON (BRIGHTEN)
Increases brightness of amber light.
F. HEATER ON/OFF
This button will turn the heater ON and OFF
independent of the main button.
G. TEMPERATURE ADJUSTMENT BUTTON
(HIGH)
Highest heat output, up to 75° F.
H. TEMPERATURE ADJUSTMENT BUTTON
(LOW.)
Low heat output, up to 72° F.
I. TEMPERATURE ADJUSTMENT BUTTON
(ROOM)
Sets the fireplace to Auto Mode (See
Opera-
tions
)
J. BLUE FLAME BUTTON (LOWER)
Reduces brightness of blue light.
K. BLUE FLAME BUTTON (HIGHER)
Increases brightness of blue light.
POWER
ON/OFF
ON/OFF
AMBER
-5 OFF
+5 MAX
HEATER
ON/OFF
TEMP. CONTROL
HIGH LOW ROOM
BLUE
-5 OFF
+5 MAX
A
C
B
E
F
D
H
G
I
J
K
REMOTE CONTROL
CAUTIONS
• Do Not Use Old Batteries With
New Ones.
• Do Not Use Batteries Other Than
The Type Specified (2 Ea. AA).
• Ensure Batteries Are Correctly
Installed In Remote Control.
FLAME
REMOTE CONTROL OPERATION STEPS:
1. For remote to function make sure the heater
is plugged-in and main power switch located
on the bottom right hand side is in the “ON”
position.
2. When operating the remote make sure you
point the remote to the center of the heater unit
and make sure each time you press the button
the LED indicator located on top right hand
corner of the remote blinks. The buzzer inside
the unit will beep once; if the LED fails to blink
check the batteries. It takes some time for the
receiver to respond to the transmit ter. Do not
PRESS the buttons more than once within two
seconds for correct operation
3. Power On power button: The power-on button
at top left corner of the remote is the main ON/
OFF power button. This will turn off all the func-
tions and the heater will be in standby mode.
4. Flame Power On button: This button controls
both the amber and blue color flame. Press this
button once to turn ON the flame effect. Once the
flame effect is ON use the + and – but tons as
explained below to adjust the flame brightness
as desired. Press this button again to turn OFF
the flame effect. The heater can function even
when the flame effect is turned off if so desired.
REMOTE CONTROL MODEL NO. R-37
PART NO. F2052
The Red Flame +5 or -5 buttons control the
brightness of the Amber fame. To increase the
brightness/flame height, press and release the
flame +5 button. Each time you press this button
the brightness will increase by a small amount,
until the maximum is reached.
Press and release the Red Flame -5 button. Each
time you press this button the brightness will
decrease by small amount, until the minimum
brightness is reached.
The Blue Flame +5 or -5 buttons control the
brightness of the Blue fame. To increase the
brightness/flame height, press and release the
Blue Flame +5 button. Each time you press this
button the brightness will increase by a small
amount, until the maximum is reached.
To decrease the brightness / flame height, press
and release the Blue Flame -5 button. Each
time you press this but ton the brightness will
decrease by small amount, until the minimum
brightness is reached.
Using these settings you can mix the amber and
the blue flame to create a realistic or stylized
flame effect. Color mixes will also be reflected
in the crystal ember bed for added impact.
5. Heater Power Button: This button is the
heater ON/OFF button. Press this button to turn
the heater ON. The heater will always turn on at
the highest setting. In order to reduce the tem-
perature on the heater press this button again.
High Button: Press the high button to switch the
heater directly to high heat setting of 1500W.
Low Button: Press the high button to switch
the heater directly to low heat setting of 750W.
Room Temp Button: Press the high but ton to
switch the heater to AUTO Mode (See Opera-
tions, Page 7).
6. To turn OFF the heater unit com-
pletely press the Power Button once.
900264-00 Rev. NC 06/14