IFM TAD 81 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 22

IFM TAD 81 Series Скачать руководство пользователя страница 6

6

Operating

mode

Output signals

2 wires

OUT:

-Analogue signal for temperature measurement

and diagnostics

3 wires

OUT1: -Switching signal for diagnostics

or

-IO-Link signal for temperature measurement and

diagnostics

OUT2: -Analogue signal for temperature measurement

and diagnostics

5.1 IO-Link

This unit has an IO-Link communication interface which enables direct access to

process and diagnostic data� In addition it is possible to set the parameters of the

unit while it is in operation� Operation of the unit via an IO-Link interface requires

an IO-Link master�
With a PC, suitable IO-Link software and an IO-Link adapter cable communication

is possible when the system is not in operation�
The IODDs necessary for the configuration of the unit, detailed information about

process data structure, diagnostic information, parameter addresses and the

necessary information about the required IO-Link hardware and software can be

found at www�ifm�com�

5.2 Analogue function

The unit converts the measured temperature value into a temperature-proportional

analogue signal�
In addition the analogue output is used for diagnostics

(→ 5.3 Diagnostic

function): The transfer of the measured temperature value is interrupted for

diagnostic messages depending on the operating mode and the setting of drEd

and an analogue signal according to NE43 of 3�5 mA (FOU2 = OFF) or 21�5 mA

(FOU2 = On) is provided�
Depending on the parameter setting

the analogue signal is within the

measuring range�

«
...
4
5
6
7
8
...
»

Содержание TAD 81 Series























Отзывы:

Нет отзывов