IFM TAD 81 Series страница 4 Скачать руководство пользователя | Manualshive

Страница: 4 / 22

background image

4

• Only use the product for its intended purpose

(→ 4 Functions and features)

�

• Only use the product for permissible media

(→ 10 Technical data)

�

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the

product must be carried out by qualified personnel authorised by the machine

operator�

• Protect units and cables against damage�

3 Getting started

Detailed description under

→ 8 Parameter setting

1� Connect unit to PC to set the parameters via the IO-Link interface�
2� Set the standard unit of measurement�

-[Uni]: °C or °F

3� Set analogue signal�

-[OU2]: I = 4��20 mA or I neg = 20��4 mA
-[ASP] and [AEP]: scaling of the measuring range�

4� Set drift monitoring�

-[drW]: drift threshold from which the unit signals "warning"�
-[drA]: drift threshold from which the unit signals "alarm"�
-[ddr]: delay time of the drift detection�

5� Select diagnostic cases that should be signalled

-[drEd]:

ON = only diagnostic cases of category "failure"

ONdr = diagnostic cases of categories "alarm" + "failure"

OFF = diagnostic cases of categories "warning" + "alarm" + "failure"

6� Configure analogue signal for diagnostic case

-[FOU2]: On = 21�5 mA or OFF = 3�5 mA

«
...
2
3
4
5
6
...
»

Содержание TAD 81 Series























Отзывы:

Нет отзывов

Похожие инструкции для TAD 81 Series

Бренд: Icom Страницы: 26

Бренд: LAUREL Страницы: 28

Бренд: Daiichi Electronics Страницы: 14

Бренд: Vectronics Страницы: 26

Бренд: Precision Electronics Страницы: 3

Бренд: Avantree Страницы: 8

Бренд: Icom Страницы: 20

Simrad CP200-5C

Бренд: Kongsberg Страницы: 110

Бренд: IFM Страницы: 5

Бренд: sauermann Страницы: 7

Бренд: Shearwater Страницы: 19

Бренд: Digi Страницы: 3

IntelliPack 801T Series

Бренд: Acromag Страницы: 20

Бренд: Acromag Страницы: 38

Бренд: Acromag Страницы: 37

Бренд: VixNet Страницы: 2

Бренд: Icom Страницы: 50

Бренд: RADEMACHER Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды