IFM TAD 81 Series Скачать руководство пользователя

Страница: 17 / 22

7 Electrical connection

The unit must be connected by a qualified electrician�

The national and international regulations for the installation of electrical

equipment must be adhered to�

Voltage supply to EN 50178, SELV, PELV / "supply class 2" to cULus�

►

Disconnect power�

►

Connect the unit as follows:

2-wire operation

3-wire operation

L+

OUT

BN
WH

BK
BU

OUT2

L+

OUT1

Colours to DIN EN 60947-5-2

BK: black, BN: brown, BU: blue, WH: white

Operation as 2-wire unit

Operation as 3-wire unit

Pin 2

= OUT

• analogue signal for temperature

and diagnostics

= OUT2

• analogue signal for temperature and

diagnostics

Pin 4

= OUT1

• switching signal for diagnostics

• IO-Link signal for temperature and

diagnostics

8 Parameter setting

Using an IO-Link capable parameter setting tool, the following options are

available:

- Reading current process values�
- Reading, changing and saving current parameter settings and transmitting

them to other units of the same type�

-Read saved diagnostic information

(→ 11)

�

Содержание TAD 81 Series























Результаты поиска

Содержание TAD 81 Series

Отзывы:

Похожие инструкции для TAD 81 Series

Бренды по названию

Популярные бренды

IFM TAD 81 Series, Руководство по эксплуатации

Результаты поиска

Содержание TAD 81 Series

Отзывы:

Похожие инструкции для TAD 81 Series

Бренды по названию

Популярные бренды