IFM Electronic LK8122 Скачать руководство пользователя страница 4

Страница: 4 / 39

1 Preliminary note

1.1 Symbols used

►

Instructions

Reaction, result

[…] Designation of keys, buttons or indications

→

Cross-reference
Important note

Non-compliance may result in malfunction or interference.
Information

Supplementary note.

CAUTION

Warning of personal injury.

Slight reversible injuries may result.

2 Safety instructions

• Please read this document prior to set-up of the unit. Ensure that the product is

suitable for your application without any restrictions.

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property can occur. That is why installation, electrical

connection, set-up, operation and maintenance of the unit must only be carried

out by qualified personnel authorised by the machine operator.

• In order to guarantee the correct condition of the device for the operating time it

is necessary to use the device only for media to which the wetted materials are

sufficiently resistant (→ Technical data).

• It is the operator's responsibility to verify whether the device is suitable for the

respective application. The manufacturer assumes no liability for consequences

of misuse by the operator.

• Improper installation and use of the device result in a loss of the warranty

claims.

• The unit complies with the standard EN 61000-6-4. The unit may cause radio

interference in domestic areas. If interference occurs, the user must take

appropriate remedial actions.

• The surface of the unit may get hot if the switching outputs are operated at

maximum load. There is a risk of burns.

Содержание LK8122








































Результаты поиска

Содержание LK8122

Отзывы:

Похожие инструкции для LK8122

Бренды по названию

Популярные бренды

IFM Electronic LK8122, Руководство по эксплуатации

Результаты поиска

Содержание LK8122

Отзывы:

Похожие инструкции для LK8122

Бренды по названию

Популярные бренды