IFM Electronic efector 300 SU9001 Скачать руководство пользователя

Страница: 4 / 31

1 Preliminary note

1.1 Symbols used

►

Instruction

Reaction, result

[…] Designation of buttons, switches or indications

→

Cross-reference
Important note

Non-compliance can result in malfunctions or interference�

2 Safety instructions

•

Please read this document prior to installing the unit� Ensure that the product is

suitable for your application without any restrictions�

•

Improper or non-intended use may lead to malfunctions of the unit or to un-

wanted effects in your application�

•

That is why installation, electrical connection, set-up, operation and mainte-

nance of the unit must be carried out by qualified personnel authorised by the

plant operator�

• In all applications test the compatibility of the product materials (→ 12 Techni

cal data) with the media to be measured�

For the scope of validity cULus:

The device shall be supplied from an isolating transformer having a secondary

Listed fuse rated as noted in the following table�

Overcurrent protection

Control-circuit wire size

Maximum protective device rating

Ampere

AWG

(mm

)

(0�13)

(0�20)

(0�32)

(0�52)

(0�82)

(1�3)

Содержание efector 300 SU9001
































Результаты поиска

Содержание efector 300 SU9001

Отзывы:

Похожие инструкции для efector 300 SU9001

Бренды по названию

Популярные бренды

IFM Electronic efector 300 SU9001, Руководство по эксплуатации

Результаты поиска

Содержание efector 300 SU9001

Отзывы:

Похожие инструкции для efector 300 SU9001

Бренды по названию

Популярные бренды