IFM Electronic efector 300 SU9001 Скачать руководство пользователя

Страница: 5 / 31

3 Functions and features

The unit monitors liquids�

It detects the 3 process categories volumetric flow, consumed quantity, medium

temperature�

Applications:

•

Water

•

Glycol solutions

• Oils (viscosity: viscosity: ≤ 68 cSt at 104°F / ≤ 68 mm²/s at 40°C)

Selection of the medium to be monitored → 9.5.9.

4 Function

4.1 Processing of the measured signals

•

The unit displays the current process values�

•

It generates 2 output signals according to the parameter setting�
OUT1: 3 selection options �� parameter setting

switching signal for volumetric flow limit values ��

(→ 9.2.1)

or pulse sequence for totalising meter ��

(→ 9.3.1)

or switching signal for preset counter ��

(→ 9.3.2)

OUT2: 4 selection options

switching signal for volumetric flow limit value ��

(→ 9.2.2)

or switching signal for temperature limit value ��

(→ 9.4.1)

or analogue signal for volumetric flow ��

(→ 9.2.3)

or analogue signal for temperature ��

(→ 9.4.2)

OUT2 (pin 2) cannot only be used as an output

but also as an input for an external reset signal:

��

(→ 9.3.5)

4.2 Volumetric flow monitoring

The flow rate is monitored by an ultrasonic meter, the measured signals by the

electronics�

•

2 switching signals for volumetric flow limit values can be provided (output 1

and output 2). For the switching functions → 4.5.

•

An analogue signal proportional to the volumetric flow (4��20 mA or 0��10 V)

can be provided on output 2. For the analogue functions → 4.6.

Содержание efector 300 SU9001
































Результаты поиска

Содержание efector 300 SU9001

Отзывы:

Похожие инструкции для efector 300 SU9001

Бренды по названию

Популярные бренды

IFM Electronic efector 300 SU9001, Руководство по эксплуатации

Результаты поиска

Содержание efector 300 SU9001

Отзывы:

Похожие инструкции для efector 300 SU9001

Бренды по названию

Популярные бренды