IFM Electronic Efector 300 SI0556 Скачать руководство пользователя страница 6

Страница: 6 / 15

4.2 Sources of interference in the pipe system

Components integrated in the pipes, bends, valves, reductions, etc lead to turbu-

lence of the medium This affects the function of the unit
Recommendation: Adhere to the distances between sensor and sources of

interference:

D = pipe diameter; S = sources of interference

4.3. Mounting operation

►

Ensure that the system is free of pressure during installation

►

Ensure that no media can leak at the mounting location during installa-

tion

►

Grease the threads of the process connection (1), adapter (2) and nut (3)

Note: The sensor tip (A) must not be in contact with grease

►

Screw the suitable adapter into the process connection

►

Place the flow monitor onto the adapter and tighten the nut Tightening torque

25 Nm Ensure that the unit is correctly oriented

Содержание Efector 300 SI0556
















Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды

IFM Electronic Efector 300 SI0556, Руководство по эксплуатации

Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды