IFM Electronic Efector 300 SI0556 Скачать руководство пользователя страница 11

Страница: 11 / 15

> After 10 s the current setting is displayed: LEDs 59 light orange (= outputs

normally open)

> After approx 15 s LEDs 04 flash orange

►

Release the pushbutton The outputs are changed to normally closed operation

For a new changeover repeat the operation

8.3 Restore the factory setting (reset)

►

Press the pushbutton for at least 15 s

> LED 9 lights, after approx 5 s it flashes

> After approx 15 s LEDs 09 flash orange

►

Release the pushbutton All settings are reset to the factory setting:

-operating area: 5 100 cm/s for water

-switch point S1 (flow): LED 7

-switch point S2 (temperature): LED 0 (4°C)

-output function: NO

-unlocked

8.4 Lock / unlock the unit

The unit can be locked electronically to prevent unintentional settings

►

Press both setting pushbuttons simultaneously for at least 10 s in the operating

mode

> The indication goes out, the unit locks or unlocks
On delivery: unlocked

Содержание Efector 300 SI0556
















Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды

IFM Electronic Efector 300 SI0556, Руководство по эксплуатации

Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды