IFM Electronic Efector 300 SI0556 Скачать руководство пользователя страница 7

Страница: 7 / 15

5 Electrical connection

The unit must be connected by a qualified electrician

The national and international regulations for the installation of electrical

equipment must be adhered to

Voltage supply to EN 50178, SELV, PELV

►

Disconnect power

►

Connect the unit as follows:

S1: flow and temperature monitoring; S2: temperature monitoring

Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

6 Operating and display elements

1: Operation display

•

The green LEDs indicate the current flow (the LEDs 0 to 9 represent the range between

no flow and maximum flow)

•

A lighting LED indicates the position of the flow switch point (S1) (orange = output

closed, red = output open)

2, 3: Setting buttons for adjustment and configuration

Содержание Efector 300 SI0556
















Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды

IFM Electronic Efector 300 SI0556, Руководство по эксплуатации

Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды