IEI Technology WAFER-945GSELVDS2 Скачать руководство пользователя

Страница: 128 / 140

WAFER-945GSELVDS2

Page 116

AC ’97

Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®

in 1997.

ACPI

Advanced Configuration and Power Interface (ACPI) is an OS-directed

configuration, power management, and thermal management interface.

AHCI

Advanced Host Controller Interface (AHCI) is a SATA Host controller

ATA

The Advanced Technology Attachment (ATA) interface connects storage

devices including hard disks and CD-ROM drives to a computer.

ARMD

An ATAPI Removable Media Device (ARMD) is any ATAPI device that

supports removable media, besides CD and DVD drives.

ASKIR

Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that

represents a digital signal by varying the amplitude (“volume”) of the

signal. A low amplitude signal represents a binary 0, while a high

amplitude signal represents a binary 1.

BIOS

The Basic Input/Output System (BIOS) is firmware that is first run when

the computer is turned on and can be configured by the end user

CODEC

The Compressor-Decompressor (CODEC) encodes and decodes digital

audio data on the system.

CompactFlash®

CompactFlash® is a solid-state storage device. CompactFlash® devices

use flash memory in a standard size enclosure. Type II is thicker than

Type I, but a Type II slot can support both types.

CMOS

Complimentary metal-oxide-conductor is an integrated circuit used in

chips like static RAM and microprocessors.

COM

COM refers to serial ports. Serial ports offer serial communication to

expansion devices. The serial port on a personal computer is usually a

male DB-9 connector.

DAC

The Digital-to-Analog Converter (DAC) converts digital signals to analog

signals.

DDR

Double Data Rate refers to a data bus transferring data on both the rising

and falling edges of the clock signal.

Содержание WAFER-945GSELVDS2













































































































































Результаты поиска

Содержание WAFER-945GSELVDS2

Отзывы:

Похожие инструкции для WAFER-945GSELVDS2

Бренды по названию

Популярные бренды

IEI Technology WAFER-945GSELVDS2, Руководство пользователя

Результаты поиска

Содержание WAFER-945GSELVDS2

Отзывы:

Похожие инструкции для WAFER-945GSELVDS2

Бренды по названию

Популярные бренды