IEI Technology WAFER-945GSELVDS2 Скачать руководство пользователя

Страница: 105 / 140

WAFER-945GSELVDS2

Page 93

5.3.7 USB Configuration

Use the

USB Configuration

menu to read USB configuration information and configure

the USB settings.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Exit

USB Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Module Version – 2.24.3-13.4

USB Devices Enabled:
None

USB Function

[Enabled]

USB 2.0 Controller

[Enabled]

Legacy USB Support

[Enabled]

USB 2.0 Controller Mode

[HiSpeed]

Options

Disabled
Enabled

ÅÆ

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 12: USB Configuration

USB Function [Enabled]

Use the

USB Functions

to enabled and disabled the USB ports.

Disabled

USB ports disabled

USB 8 ports

Only the USB ports on the rear I/O panel are

activated

Enabled D

EFAULT

All the USB ports are enabled

USB 2.0 Controller [Enabled]

Use the

USB 2.0 Controller

BIOS option to enable or disable the USB 2.0 controller

Disabled

USB 2.0 controller disabled

Enabled D

EFAULT

USB 2.0 controller enabled

Содержание WAFER-945GSELVDS2













































































































































Результаты поиска

Содержание WAFER-945GSELVDS2

Отзывы:

Похожие инструкции для WAFER-945GSELVDS2

Бренды по названию

Популярные бренды

IEI Technology WAFER-945GSELVDS2, Руководство пользователя

Результаты поиска

Содержание WAFER-945GSELVDS2

Отзывы:

Похожие инструкции для WAFER-945GSELVDS2

Бренды по названию

Популярные бренды