IEI Technology ISP-9652/9602 Скачать руководство пользователя страница 84

Страница: 84 / 119

ISP-9652/9602 User Manual

Page 72

PWM Maximum Mode: 127

Slope PWM [1 PWM]

A bigger value will increase the fan speed in big amounts. A smaller value will increase the

speed more gradually.

PWM

CPU Fan PWM Control [070]

This value specifies the speed of the fan.

PWM Minimum Mode: 0

PWM Maximum Mode: 127

H/W Health Function [Enabled]

Use the

H/W Health Function

to enable the monitoring of the system environmental

parameters.

Disabled

Disables the health monitoring function

Enabled D

EFAULT

Enables the health monitoring function

Hardware Health Monitoring

The following system parameters and values are shown. The system parameters that are

monitored are:

System

Temperatures:

CPU Temperature

Содержание ISP-9652/9602
























































































































Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology ISP-9652/9602, Руководство пользователя

Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Бренды по названию

Популярные бренды