IEI Technology ISP-9652/9602 Скачать руководство пользователя страница 14

Страница: 14 / 119

ISP-9652/9602 User Manual

Page 2

1.1 Introduction

Figure 1-1: ISP-9652/9602

The ISP-9652/9602 MicroATX motherboard is a Socket P Intel® Core™2 Duo and Intel®

Celeron® M processor platform. 45nm core and 65nm core processors are supported.

Up to two 2.0 GB 667/533 MHz are supported by the Intel® GME965 graphics memory

controller hub (GMCH) on the ISP-9652, while the Intel® GML960 on the ISP-9602

supports two 1.0 GB 533 MHz DDR2 SDRAM DIMMs. Both included an onboard VGA

output.

The integrated Intel® ICH8M I/O controller hub (ICH) supports three SATA 3Gb/s drives

with data transfer speeds of 3.0 Gbps. Ten USB 2.0 channels and one expansion PCI

socket provide flexible expansion options. The ISP-9652 also provides PCIe x16

expansion through an edge connector.

The ISP-9652/9602 features four GbE LAN connections with two dual-group LAN bypass

function. In the event of a failure the hardware LAN bypass will be activated to ensure

essential network communications will continue. Two additional GbE LAN ports without

LAN bypass are included.

Содержание ISP-9652/9602
























































































































Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology ISP-9652/9602, Руководство пользователя

Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Бренды по названию

Популярные бренды