IEI Technology ISP-9652/9602 Скачать руководство пользователя страница 46

Страница: 46 / 119

ISP-9652/9602 User Manual

Page 34

4.2.2 Installation Checklist

The following checklist is provided to ensure the ISP-9652/9602 is properly installed.

All the items in the packing list are present

A compatible memory module is properly inserted into the slot

The CF Type I or CF Type II card is properly installed into the CF socket

The jumpers have been properly configured

The ISP-9652/9602 is inserted into a chassis with adequate ventilation

The correct power supply is being used

The following devices are properly connected

SATA drives

Power supply

USB cable

Serial port cable

The following external peripheral devices are properly connected to the

chassis:

VGA screen

RS-232 serial communications device

USB devices

4.3 Unpacking

When the ISP-9652/9602 is unpacked, please check all the unpacking list items listed in

Chapter 3 are present. If any of the unpacking list items are not available please contact

the ISP-9652/9602 reseller/vendor where the ISP-9652/9602 was purchased or contact an

IEI sales representative.

Содержание ISP-9652/9602
























































































































Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Похожие инструкции для ISP-9652/9602

Бренды по названию

Популярные бренды

IEI Technology ISP-9652/9602, Руководство пользователя

Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Похожие инструкции для ISP-9652/9602

Бренды по названию

Популярные бренды