IEI Technology ISP-9652/9602 Скачать руководство пользователя страница 104

Страница: 104 / 119

ISP-9652/9602 User Manual

Page 92

Below is a list of BIOS configuration options in the BIOS chapter.

System Overview .................................................................................................................59

System Time [xx:xx:xx] .......................................................................................................60

System Date [xx/xx/xx] ........................................................................................................60

ATA/IDE Configuration [Compatible].................................................................................62

Configure SATA as [IDE].....................................................................................................63

IDE Master and IDE Slave....................................................................................................63

Auto-Detected Drive Parameters........................................................................................64

Type [Auto] ...........................................................................................................................65

LBA/Large Mode [Auto].......................................................................................................65

Block (Multi Sector Transfer) [Auto] ..................................................................................66

PIO Mode [Auto]...................................................................................................................66

DMA Mode [Auto].................................................................................................................66

S.M.A.R.T [Auto]...................................................................................................................68

32Bit Data Transfer [Enabled].............................................................................................68

Serial Port1 Address [3E8]..................................................................................................69

Serial Port2 Address [2E8]..................................................................................................69

Mode Setting [Full On Mode] ..............................................................................................70

Temp. Limit of OFF [000].....................................................................................................71

Temp. Limit of Start [020]....................................................................................................71

Start PWM [070]....................................................................................................................71

Slope PWM [1 PWM] ............................................................................................................72

CPU Fan PWM Control [070] ...............................................................................................72

H/W Health Function [Enabled] ..........................................................................................72

Hardware Health Monitoring ...............................................................................................72

Remote Access [Disabled]..................................................................................................74

Serial Port Number [COM1].................................................................................................74

Base Address, IRQ [3E8h, A] ..............................................................................................74

Serial Port Mode [115200 8,n,1] ..........................................................................................74

Redirection After BIOS POST [Always] .............................................................................75

Terminal Type [ANSI]...........................................................................................................75

USB Configuration...............................................................................................................76

USB Devices Enabled..........................................................................................................76

USB Function [Enabled]......................................................................................................76

Содержание ISP-9652/9602
























































































































Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology ISP-9652/9602, Руководство пользователя

Результаты поиска

Содержание ISP-9652/9602

Отзывы:

Бренды по названию

Популярные бренды