IEI Technology IMBA-9454B Скачать руководство пользователя страница 18

Страница: 18 / 192

IMBA-9454B ATX Motherboard

Page 2

1.1 Introduction

The IMBA-9454B motherboard has an LGA775 socket for Intel® processors. The

IMBA-9454B offers eight RS-232 serial ports and two VGA outputs. Four of the RS-232

ports support power through pin-9 supporting either the standard RI signal, 5 V or 12 V

power. The VGA ports support three display modes. The first mode support display of the

same output on both monitors. The second supports display of two different pictures on

both. Finally, extended view spreads a single output image over two monitors installed

next to each other, or above each other.

The IMBA-9454B also features six USB ports, four SATA II ports, an IDE port, a FDD port,

a parallel port, three PCI slots, a PCIe x1 slot and a PCIe Mini card slot.

1.2 Features

Some of the IMBA-9454B features are listed below.

RoHS

compliant

Supports Intel® Core™2 Duo, Pentium® 4, Pentium® D and Celeron® D

Integrated Intel® GMA950 graphics engine

Maximum FSB of 1066 MHz

Two DDR2 DIMMs up to 2.0 GB each

High performance PCIe Gigabit Ethernet chipset

Four SATA 3.0 Gb/s drives supported

Two Ultra ATA 100 IDE devices supported

Six USB 2.0 devices supported

Expansion:

1 x PCIe x1 expansion slot

1 x PCIe Mini card slot

3 x PCI slots

1.3 Overview

The diagram below shows the connectors on the IMBA-9454B.

Содержание IMBA-9454B

































































































































































































Результаты поиска

Содержание IMBA-9454B

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMBA-9454B, Руководство пользователя

Результаты поиска

Содержание IMBA-9454B

Отзывы:

Бренды по названию

Популярные бренды