IEI Technology IMBA-9454B Скачать руководство пользователя страница 169

Страница: 169 / 192

IMBA-9454B ATX Motherboard

Page 153

NOTE:

The following discussion applies to DOS environment. IEI support is

contacted or the IEI website visited for specific drivers for more

sophisticated operating systems, e.g., Windows and Linux.

The Watchdog Timer is provided to ensure that standalone systems can always recover

from catastrophic conditions that cause the CPU to crash. This condition may have

occurred by external EMIs or a software bug. When the CPU stops working correctly,

Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt

(NMI) to bring the system back to a known state.

A BIOS function call (INT 15H) is used to control the Watchdog Timer.

INT 15H:

AH – 6FH Sub-function:

AL – 2:

Sets the Watchdog Timer’s period.

BL:

Time-out value (Its unit-second is dependent on the item “Watchdog

Timer unit select” in CMOS setup).

Table D-1: AH-6FH Sub-function

Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value

is not zero, the Watchdog Timer starts counting down. When the timer value reaches zero,

the system resets. To ensure that this reset condition does not occur, calling sub-function

2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled

if the time-out value is set to zero.

A tolerance of at least 10% must be maintained to avoid unknown routines within the

operating system (DOS), such as disk I/O that can be very time-consuming.

Содержание IMBA-9454B

































































































































































































Результаты поиска

Содержание IMBA-9454B

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMBA-9454B, Руководство пользователя

Результаты поиска

Содержание IMBA-9454B

Отзывы:

Бренды по названию

Популярные бренды