IEI Technology Enano-8523T Скачать руководство пользователя страница 64

Страница: 64 / 164

-64

1 x Mini jumper pack

1 x Utility CD

1 x IDE flat cable 44p/44p

1 x QIG (quick installation guide)

If one or more of these items are missing, please contact the reseller or vendor you

purchased the Enano-8523T board from and do not proceed any further with the

installation.

4.3

Enano-8523T Board Installation

WARNING!

1. Never run the Enano-8523Twithout an appropriate heatsink and cooler

that can be ordered from IEI Technology or purchased separately.

Be sure to use the CPU 12V power connector (CN10007) for the CPU

power.

WARNING!

Please note that the installation instructions described in this manual should

be carefully followed in order to avoid damage to the Enano-8523T

components and injury to you.

WARNING!

When installing electronic components onto the Enano-8523T always take the

following anti-static precautions in order to prevent ESD damage to your

Enano-8523T and other electronic components like the CPU and DIMM

modules

4.3.1 Preinstalled Components

The components listed below are preinstalled on the Enano-8523T.

IEI

Technology, Corp

Содержание Enano-8523T





































































































































































Результаты поиска

Содержание Enano-8523T

Отзывы:

Похожие инструкции для Enano-8523T

Бренды по названию

Популярные бренды

IEI Technology Enano-8523T, Руководство пользователя

Результаты поиска

Содержание Enano-8523T

Отзывы:

Похожие инструкции для Enano-8523T

Бренды по названию

Популярные бренды