IEI Technology Enano-8523T Скачать руководство пользователя страница 94

Страница: 94 / 164

-94

Disabled

USB

function

disabled

Enabled

(Default) USB

function

enabled

Legacy USB Support [Disabled]

The

Legacy USB Support

BIOS option refers to USB mouse and USB keyboard support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded on the system.

Disabled

(Default)

Legacy USB support disabled

Enabled

Legacy USB support enabled

USB 2.0 Controller [Enabled]

The

USB 2.0 Controller

BIOS option enables or disables the USB 2.0 controller

Disabled

USB

function

disabled

Enabled

(Default) USB

function

enabled

USB2.0 Controller Mode [HiSpeed]

The

USB2.0 Controller Mode

BIOS option allows you to set the speed of the USB2.0

controller.

FullSpeed

The controller is capable of operating at full speed

(12Mbits/second)

HiSpeed

(Default)

The controller is capable of operating at high speed

(480Mbits/second)

USB Mass Storage Device Configuration

IEI

Technology, Corp

Содержание Enano-8523T





































































































































































Результаты поиска

Содержание Enano-8523T

Отзывы:

Похожие инструкции для Enano-8523T

Бренды по названию

Популярные бренды

IEI Technology Enano-8523T, Руководство пользователя

Результаты поиска

Содержание Enano-8523T

Отзывы:

Похожие инструкции для Enano-8523T

Бренды по названию

Популярные бренды