IEI Technology Enano-8523T Скачать руководство пользователя страница 77

Страница: 77 / 164

-77

Enano-8523T Motherboard

Secondary Slave)

Both

(Default) Allows the system to detect both the Primary and

Secondary IDE channels including the Primary Master,

Primary Slave, Secondary Master and Secondary Slave.

IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. This displays the

status of the auto detected IDE devices. The following IDE devices are detected and are

shown in the IDE Configuration menu:

Primary IDE Master

Primary IDE Slave

Secondary IDE Master

Secondary IDE Slave

Third IDE Master

Third IDE Slave

The

IDE Configuration

menu (

BIOS Menu 4

) allows you to set or change the

configurations for the IDE devices installed in the system. If an IDE device is detected, and

one of the above listed four BIOS configuration options are selected, the IDE configuration

options shown in

Section 5.3.2.1

appear.

5.3.2.1 IDE Master, IDE Slave

IDE Master and IDE Slave configuration options for both primary and secondary IDE

devices are shown in the BIOS menu below.

Содержание Enano-8523T





































































































































































Результаты поиска

Содержание Enano-8523T

Отзывы:

Похожие инструкции для Enano-8523T

Бренды по названию

Популярные бренды

IEI Technology Enano-8523T, Руководство пользователя

Результаты поиска

Содержание Enano-8523T

Отзывы:

Похожие инструкции для Enano-8523T

Бренды по названию

Популярные бренды