IDENTEC SOLUTIONS iPOINT Si Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 26

background image

iPOINT – Hardware User Manual | 18.06.2020

Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.

18

4. Mechanical Information & Installation

Housing Dimensions

4.1 Opening the connection Chamber

1. Lift up the cover using thumbs from the front side until magnetic connection is released, lift off.

2. Loosen the 8x screws, be aware, DO NOT pull out the screws out completely, the gasket can be damaged.

3. Lift off the lid.

4. Now you have access to the Connection Chamber

Note:

when replacing the lid, be sure that the sealing gasket is correctly in place.

Note

: The rest of the housing cannot be accessed. There is no settings or modifications to be made there.

«
...
16
17
18
19
20
...
»

Содержание iPOINT Si



























Отзывы:

Нет отзывов

Похожие инструкции для iPOINT Si

Бренд: JBL Страницы: 16

Authentics L 16

Бренд: JBL Страницы: 17

Бренд: QUALITY LIFTS Страницы: 21

Бренд: WAGO Страницы: 18

Бренд: WAGO Страницы: 46

EAGLE GRIP EG4MDC2-F

Бренд: Easy Lift Equipment Страницы: 17

Бренд: Rotary Страницы: 16

BeoSound 3000 2671

Бренд: Bang & Olufsen Страницы: 68

Бренд: 2VV Страницы: 29

Бренд: RAPIBREW Страницы: 67

RAV6351 ILPVS1340

Бренд: rav Страницы: 152

PIO-32/32RL(PCI)H

Бренд: Contec Страницы: 4

Connect Control Box

Бренд: Grainfather Страницы: 9

Бренд: SereneLife Страницы: 2

Бренд: ETC Страницы: 386

Бренд: Blaupunkt Страницы: 8

Бренд: Sharp Страницы: 72

Бренд: Panasonic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды