background image

 

VISIBILITY DELIVERED. 

PAGE 11 OF 15 

2

 

Configuration of the tag 

The i-B350L 

S

 is configured using the i-PROG M350L programming device. 

 

Important Note 

Do not open the housing! Configuration is done using the built-in air interface of the i-B350L 

S

 
In addition to the Broadcast mode the i-B350L 

S

 offers the following special functions that can be configured: 

 

 

Bursts on entering a marker field can be configured independent from regular Pings 

 

Marker technology 

 

Bursts triggered by the push button can be configured independent from regular Pings 

 

Tools Needed 

 

PC running on MS Windows with the ILR Tag Configuration for ILR 350 series tags 

 

Connected to an i-PROG M350L to configure the tags 

 
The ILR Tag Configuration software tool is described in detail in this manual: 
 

 

ILR 350 Tag Configuration Plug-In Manual 

 

Overview on the Configuration Software 

 

 

Select Ping Rate and Ping 
Message Content in the block 
―Broadcast‖ 

Select Burst behavior on 
entering a marker field in 
the block ―Marker‖ 

Select Burst behavior when 
the button is pressed in the 
block ―Push Button‖ 

Содержание i-B350 S
















Отзывы: