IDEAL TILT-A WAY HYJG 1, Руководство оператора и каталог запасных частей

Страница: 6 / 131

IMPORTANT SAFETY INFORMATION
1
Before installing the installer should read and understand the owners manual and safety instructions. The owner should read,
and keep this owners manual. Read and Follow All Instructions.
WARNING-TO REDUCE THE RISK OF INJURY OR DEATH TO PERSONS
1. Do not operate gate unless all safety devices are connected and working properly.
2. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. Do not adjust pressure
relief valve to compensate for an improperly installed, improperly functioning, or damaged gate.
3. Do not permit children to play on or around a gate. Keep all controls out of reach from children.
4. Automatic gates are not intended for pedestrian use. Pedestrians must be supplied a separate entrance separate from the automatic gate.
5. Never operate an automatic gate system without visual contact so it can be shut down if necessary.
6. Permanently mounted controls intended for user activation must be located at least 6 feet away from the gate and operator.
7. Disconnect all power before performing any maintenance on your gate or operator.
8. Keep your gate properly maintained-have a qualified service person make all repairs.
9. A qualified technician should test your gate monthly. The gate MUST reverse on contact with a rigid object. After adjusting the force of the
limit of travel, retest the gate operator. Failure to adjust and retest the gate operator properly can increase the risk of injury or death.
10. The gate and operator must have two appropriate safety devices to match the gate class installation. Type A – inherent, and Type B2- Contact
sensor.
11. Operator and barrier must display warning signs on both sides, in view of operator.
12. Do not install added weight to the gate barrier, your barrier has been balanced at the factory, if you add weight to the barrier it will make your
gate out of balance, which could cause it to malfunction.
13. Before turning the power on make sure that the correct voltage has been supplied to the electric motor and the equipment has been properly
grounded.
14. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
15. Only qualified personnel should install this equipment. Failure to meet this requirement could cause severe injury and or death, for which the
manufacturer cannot be held responsible.
CLASS OF VEHICULAR GATES
Glossary
CLASS I-RESIDENTIAL VEHICULAR GATE OPERATOR (3.19)
A vehicular gate operator (or system) intended for use in garages or parking areas associated with a residence of one to four single families.
CLASS II-COMMERCIAL/GENERAL ACCESS VEHICULAR GATE OPERATOR (3.4)
A vehicular gate operator (or system) intended for use in a commercial location or building such as multi-family housing unit (five or more single
family unit), hotel, garages, retail store, or other buildings accessible by of servicing the general public.
CLASS III-INDUSTRIAL/LIMITED ACCESS VEHICULAR GATE OPERATOR (3.11)
A vehicular gate operator (or system) intended for use in an industrial location or building such as a factory or loading dock area or other locations
not accessible by or intended to service the general public.
CLASS IV-RESTRICTED ACCESS VEHICULAR GATE OPERATOR (3.20)
A vehicular gate operator (or system) intended for use in a guarded industrial location or building such as an airport security area or other
restricted access locations not servicing the general public, in which unauthorized access
is
prevented via supervision by security personal.
INSTRUCTIONS FOR MANUAL OPERATION TILT-A-WAY MODEL HYJG
Note: Use the manual operation only when the gate is not moving and with the power turned off
1. Locate two Brass colored knurled knobs on the top of the pump housing
2. (If equipped with a cold weather package, lift flap on the black cover to access knobs.)
3. Turn both knobs counter clockwise one full turn to open.
4. Gate barrier can now be lifted manually from out at the end of gate.
5. Turn knobs clockwise to close, then operate gate normally.
PROTECTION AGAINST ENTRAPMENT
Gate operator category
Horizontal slide, vertical lift. and vertical pivot Swing and vertical barrier (arm)
Entrapment protection types (a) Entrapment protection types (a)
A, B1, B2, or D A, B1, B2, C, OR D
Note-The same type of device shall not be utilized for both entrapment protection means. Use of a single device to cover both the opening and closing directions is
in accordance with the requirement; however, a single device is not required to cover both directions. A combination of one Type B1 for one direction and one
Type B2 for the other direction is the equivalent of one device for the purpose of complying with the requirements of either entrapment protection means.
(a) Entrapment protection types:
Type A – Inherent entrapment protection system. See 31.1.5.
Type B1 –Non-contact sensor (photoelectric sensor or the equivalent). See 31.1.6 – 31.1.9.
Type B2 –Contact sensor (edge device or the equivalent). See 31.1.7 and 31.1.11 – 31.1.13.
Type C – Inherent force limiting, inherent adjustable clutch or inherent pressure relief device. See 31.1.15 and 31.2.1.2 (b).
Type D –Actuating device requiring continuous pressure to maintain opening or closing motion of the gate. See 31.1.16 and 31.1.17.