Ideal Boilers 4100 4125 Скачать руководство пользователя страница 30

Страница: 30 / 44

SERVICING

Mexico Super 4100 FF & 4125 FF -

Installation

58 BURNER AND CONTROLS ASSEMBLY REMOVAL

1. Remove the silicon rubber tube from the fan sensing

point.

2. Disconnect the fan leads.

3. Remove the M4 screw securing the flue connector to the

fan.

4. Slacken the M4 screw securing the flue connector to the

turret front panel.

5. Disconnect the silicon rubber tube from the top of the

collector hood.

6. Remove the 4 M4 screws on the top of the collector hood

and by sliding it forwards remove collector hood/fan
assembly.

7. Check that the fan impellor runs freely. Remove any

debris from the impellor with a soft brush.

8. Remove the flue baffles.

9. Remove all loose deposits from the heat exchanger,

particularly between the fins, using a suitable brush.

10. Re-assemble in reverse order. Lubricate fan 'O' ring with

silicon grease. Ensure the fan leads and 2 sensing tubes
are connected.

59 CLEANING THE BURNER / PILOT ASSEMBLY

1. Brush off any deposits that may have fallen onto the

burner head (ensuring that the flame ports are
unobstructed) and remove any debris that may have
collected.

Note.

Brushes with metallic bristles MUST NOT be

used.

2. Remove the main burner injector .Check, clean or

replace, as required.

3. Refit the injector, using an approved jointing compound.

4. Inspect the pilot burner and ignition/detection electrode;

ensure they are clear and in good condition.

Check that:

a. The pilot burner is clean and unobstructed.

b. The ignition/detection electrode is clean and

undamaged.

c. The ignition/detection lead is in good condition and

securely connected.

d. The spark gap is correct. Refer to Frame 69.

e. The position of the ignition/detection electrode relative

to the pilot burner is correct. Refer to Frame 69.

5. Clean or renew components as necessary.

60 CLEANING THE FAN/FLUEWAYS

1. Remove the 2 screws and lift off the lower

front panel. Refer to Frame 57.

2. Remove the grille

assembly. Undo the gas
cock union.

3. Disconnect the ignition

lead from the PCB.

4. Remove the 4 wing nuts

and withdraw the burner
and controls assembly,
complete, from the boiler.

5. Place on a convenient

working surface.

SER

VICING

Содержание 4100 4125













































Результаты поиска

Содержание 4100 4125

Отзывы:

Похожие инструкции для 4100 4125

Бренды по названию

Популярные бренды

Ideal Boilers 4100 4125, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100 4125

Отзывы:

Похожие инструкции для 4100 4125

Бренды по названию

Популярные бренды