Ideal Boilers 4100 4125 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 44

background image

17

INSTALLATION

T

OP FLUE OUTLET

Mexico Super 4100 FF & 4125 FF -

Installation

26 TOP FLUE OUTLET ASSEMBLY - 100 FF ONLY - Exploded view

1. The boiler turret assembly is factory built for rear flue

installation.

2. Remove the turret access cover.

3. Remove the sealing plate from the turret access cover

and refit in the rear outlet.

IMPORTANT
The maximum total equivalent horizontal flue length is 2m
for 100 FF model.
For the number of extension ducts required see Frame 36.

LEGEND
1. Terminal.
2. Weather seal.
3. Flue assembly.
4. Boiler sealing ring.
5. Flue extension tube (short).
6. Elbow.
7. Flue connector.
8. Turret access cover.

4. Fit the outlet flue elbow pointing upwards, rotate in

the bayonet slot and secure with the M4 screw.

5. Fit the short extension tube (with no ring) to the flue

elbow, rotate in the bayonet slot and secure with the
M4 screw.

6. An optional flue duct extension kit is required for

lengths (distance from the outside wall to the
relevant side of the boiler casing) greater than
600mm (23

1/2

") Refer to Frame 7.

7. When cutting the ducts always use the cardboard

support provided.

27 PREPARING THE WALL

1. Mark onto the wall the position of the flue duct

hole.

IMPORTANT. Ensure that, during the cutting
operation, masonry falling outside of the building
does not cause damage or personal injury.

2. Cut the flue hole, preferably with a 125mm (5")

core boring tool, ensuring that the hole is
square to the wall. If the hole has been quite
accurately cut with a drill then making good the
wall faces is not essential as seals are provided
at both ends of the flue. However, both wall
faces immediately around the cut hole should
be flat; make good if necessary. For less
accurate holes make good to approximately
125mm (5") diameter at the 2 wall faces.

Note.

If the

terminal is to be
sited within 25-
40mm of a
corner or
vertical pipe
(refer to Table 3)
then the hole
MUST be
accurately cut
and the rubber
weather seal
trimmed around
the groove
provided.
The terminal
wall plate need
not be fitted.

«
...
15
16
17
18
19
...
»

Содержание 4100 4125













































Отзывы:

Нет отзывов

Похожие инструкции для 4100 4125

ULTRA-MAX 8024CBA

Бренд: Star Страницы: 20

Бренд: Kordi Страницы: 20

WBS Active seried

Бренд: Sun System Страницы: 16

Бренд: Alpha Boilers Страницы: 36

Бренд: Chaffoteaux & Maury Страницы: 12

Бренд: Potterton Страницы: 36

Бренд: Potterton Страницы: 28

Vitocrossal CRU 1000

Бренд: Viessmann Страницы: 72

Бренд: Baxi Potterton Страницы: 40

Бренд: Weil-McLain Страницы: 4

Бренд: Weil-McLain Страницы: 22

Бренд: Riello Страницы: 52

Бренд: Hydro-Smart Страницы: 32

Бренд: Unical Страницы: 33

Stainless Lite HP Indirect 180-400 litres

Бренд: gledhill Страницы: 36

Бренд: Ferroli Страницы: 48

Бренд: Vaillant Страницы: 52

BlueHelix HiTech RRT C

Бренд: Ferroli Страницы: 356

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды