Ideal Boilers 4100 4125 Скачать руководство пользователя страница 9

Страница: 9 / 44

Mexico Super 4100 FF & 4125 FF -

Installation

INSTALLATION

INST

ALLA

TION

BOILER CASING REMOVAL

To install the boiler the casing MUST be removed.

1. Undo the 2 screws and lift off the lower front panel.

2. Remove 2 screws and lift off the grille assembly.

3. Disconnect the in-line electrical connector between

the control box and the PCB box.

4. Remove the thermostat phial from the pocket as

shown in Frame 6.

The boiler is supplied fully assembled in Pack A,
together with a standard flue assembly for lengths
up to 600mm (23

1/2

") rear or side flue outlet in

Pack B.

Unpack and check the contents.

UNPACKING

complete boiler assembly

BOILER HARDWARE PACK

1" BSP plugs - 5 off.

1" x

1/2

" BSP reducing bush - 1 off.

Distributor tube - 1off.

28mm Comp nut - 1off.

28mm Olive - 1off.

Thermostat pocket -1 off

Thermostat clip (RS 3/50, RS 3/60,
RS 3/70 & RS 3/80 only) - 1 off

Thermostat retaining pin - 1 off

FLUE PACK. Pack B Contents

Duct cutting support, 2 off (cardboard ).

Terminal wall plate, 1 off.

Terminal grille assy., 1 off.

Polyurethane foam seal 400 lg., 1 off.

No. 8 x 8 lg. Pozi pan hd. screws, 3 off.

FLUE HARDWARE PACK

Flue extension tube (rear)

Flue extension tube (side)

Flue extension tube (top)

Elbow

Sealing ring

M5 wing nuts - 3 off

No.10 x 2” Rd. Hd.
woodscrew - 8 off.

Wall Plug - brown - 8 off.

Side outlet plate

PACK A CONTENTS

complete boiler assembly.

User's Instructions.

these Installation and Servicing Instructions.

the Hardware Pack (listed separately below).

Template.

Cable strap - 2 off.

INST

ALLA

TION

Содержание 4100 4125













































Результаты поиска

Содержание 4100 4125

Отзывы:

Похожие инструкции для 4100 4125

Бренды по названию

Популярные бренды

Ideal Boilers 4100 4125, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100 4125

Отзывы:

Похожие инструкции для 4100 4125

Бренды по названию

Популярные бренды