manualshive.com logo in svg

ICS Schneider Messtechnik IPT-2x, Инструкция по эксплуатации

Поделиться
Скачать
ICS Schneider Messtechnik IPT-2x Скачать руководство пользователя страница 21

21

5 Connecting to power supply

WIKA Operating Instructions - Process pressure transmitter IPT-2x

5 

Connecting to power supply

5.1  Preparing the connection

Always keep in mind the following safety instructions:

•

Carry out electrical connection by trained, qualified personnel 

authorised by the plant operator

•

If overvoltage surges are expected, overvoltage arresters should 
be installed

Warning:

Only connect or disconnect in de-energized state.

Power supply and current signal are carried on the same two-wire 

cable. The operating voltage can differ depending on the instrument 

version.

The data for power supply are specified in chapter "

Technical data

".

Provide a reliable separation between the supply circuit and the 
mains circuits according to DIN EN 61140 VDE 0140-1.

Power the instrument via an energy-limited circuit acc. to IEC 61010-
1, e.g. via Class 2 power supply unit.

Keep in mind the following additional factors that influence the operat

-

ing voltage:

•

Lower output voltage of the power supply unit under nominal load 
(e.g. with a sensor current of 20.5 mA or 22 mA in case of fault)

•

Influence of additional instruments in the circuit (see load values in 

chapter "

Technical data

")

The instrument is connected with standard two-wire cable without 

shielding. If electromagnetic interference is expected which is above 
the test values of EN 61326-1 for industrial areas, shielded cable 
should be used.

Use cable with round cross section for instruments with housing and 
cable gland. Use a cable gland suitable for the cable diameter to 

ensure the seal effect of the cable gland (IP protection rating).

If shielded cable is required, we recommend connecting the cable 
screening on both ends to ground potential. In the sensor, the cable 
screening must be connected directly to the internal ground terminal. 
The ground terminal on the outside of the housing must be connected 
to the ground potential (low impedance).

In Ex systems, the grounding is carried out according to the installa-
tion regulations.

In electroplating plants as well as plants for cathodic corrosion protec-

tion it must be taken into account that significant potential differences 

exist. This can lead to unacceptably high currents in the cable screen 
if it is grounded at both ends.

Safety instructions

Voltage supply

Connection cable

Cable screening and 
grounding

Содержание IPT-2x

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды