background image

IM242S       

                                                                                                                               

     

User Manual

 

12 

performance close to the Shannon limit when decoded with the belief-propagation (BP) algorithm 
using soft-decision information.   

3.4 Wear-Leveling 

Flash memory can be erased within a limited number of times. This number is called the

 

erase 

cycle limit

 

or

 

write endurance

 

limit

 

and is defined by the flash array vendor. The erase cycle 

limit applies to each individual erase block in the flash device.   

ICOP IM242S uses a static wear-leveling algorithm to ensure that consecutive writes of a specific 
sector are not written physically to the same page/block in the flash. This spreads flash media 
usage evenly across all pages, thereby extending flash lifetime. 

3.5 Bad Blocks Management 

Bad Blocks are blocks that contain one or more invalid bits whose reliability are not guaranteed. 
The Bad Blocks may be presented while the SSD is shipped, or may develop during the life time 
of the SSD. When the Bad Blocks is detected, it will be flagged, and not be used anymore. The 
SSD implement Bad Blocks management, Bad Blocks replacement, Error Correct Code to avoid 
data error occurred. The functions will be enabled automatically to transfer data from Bad Blocks 
to spare blocks, and correct error bit. 

3.6 Power Cycling 

ICOP’s power cycling management is a comprehensive data protection mechanism that functions 
before and after a sudden power outage to SSD. Low-power detection terminates data writing 
before an abnormal power-off, while table-remapping after power-on deletes corrupt data and 
maintains  data  integrity.  ICOP’s  power  cycling  provides  effective  power  cycling  management, 
preventing data stored in flash from degrading with use. 

3.7 Garbage Collection 

Garbage collection is used to maintain data consistency and perform continual data cleansing on 
SSDs.  It  runs as a background process, freeing up valuable controller resources while sorting 
good  data  into  available  blocks,  and  deleting  bad  blocks.  It  also  significantly  reduces  write 
operations to the drive, thereby increasing the SSD’s speed and lifespan.   

 

 

Содержание IM242S Series














Отзывы: