Ice iS1100 Скачать руководство пользователя

Страница: 26 / 62

ICE iS1100

OPERATOR

TROUBLESHOOTING

Trouble

Possible cause

Remedy

The machine does not start when

turning the ignition key to “I”.

The battery connector (44) is

disconnected.

Connect the battery connector.

The fM fuse in the holder (54) is open. Replace the fM fuse.

The battery charger cable is connected

to the electrical mains.

Disconnect the battery charger cable

from the electrical mains.

The main brush does not work.

The main brush microswitch faulty.

Replace the main brush microswitch.

The side brushes do not operate. The main brush is not lowered.

Lower the main brush.

The side brush microswitch faulty.

Replace the side brush microswitch.

The machine operates only when

stationary, otherwise battery level

indicator begins flashing,.

The batteries are discharged.

Charge the batteries.

If the problem persists, replace the

battery.

The battery autonomy is low.

The batteries are dead.

Replace the batteries.

The battery capacity is low.

Buy batteries with higher capacity

(see the Technical Data paragraph).

SCRAPPING

Have the machine scrapped by a qualified scrapper.

Before scrapping the machine, remove and separate the following materials, which must be disposed of properly

according to the Law in force:

- Batteries - Engine oil

- Polyester dust filter - Main and side brushes

- Plastic hoses and components - Electrical and electronic components (*)

(*) Refer to the nearest ICE Center especially when scrapping electrical and electronic components.

ALARMS

Active alarms are shown on the display.

Alarm #id

Meaning

Action

f01:Seat Empty

No sit in the seat or Seat circuit open

Sit in the operator seat or Check circuit

f04:Vac Mtr O.L RE-START

Vac Mtr ammeter protection

Verify vacuum motor working current value

f05:Main Bru Mtr O.L RE-START

Main bru mtr ammeter protection

Verify main bru motor working current value

f06:Side Bru Mtr O.L RE-START

Side bru mtr ammeter protection

Verify side bru motor working current value

f07:Propel Mtr O.L

Propel Motor ammeter protection

Verify Propel Motor current value

f10:Batt Low Charge batt

Battery is low

Charging the battery

f11:Batt Very Low Charge batt

NOW!!

Battery is very low

Charging the battery

f12:Brake Wiring Error

Brake circuit open

Check brake wirings and circuit

f13:Release foot Pedal

Steping the foot pedal when starting

machine

Release the foot pedal when turn on the machine

f14:Replace Brake Assy

Brake circuit short

Check brake wirings and circuit

f16:Control Unit Overheat! Wait

Over Temp or Control Unit fault

Verify motor working current value or Change

Control Unit

f17:Replace Control Unit

Temp. Sensor failure

ChangeControl Unit

f18:Replace foot Pedal Assy

foot Pedal Sensor failure

Verify pedal wirings and pedal sensor

f20:Check Main Brush Motor

Main Motor error or circuit open

Verify wirings and main brush motor

f21:Check Vac Mtr

Vac Motor error or circuit open

Verify wirings and vac motor

f24:Check Propel Motor

Propel Motor error or circuit open

Verify wirings and propel motor

f25:Check Side Brush Motor

Side Brush Motor error or circuit open

Verify wirings and side brush motors

f40:Check Proximity Sw

Sw Sensor failure

Change Sw Sensor

f42:Replace Control Unit

Relay Contact error

Change Control Unit

f43:Turn Dead Sw Off RE-START

Emergency stop button be actived or

circuit open

Reset emergency stop button,restart the machine

or check circuit

f44:Replace Control Unit

Control Unit fault

Change Control Unit

f45:Return Control Unit

Control Unit fault

Change Control Unit

f46:Return Control Unit

Control Unit fault

Change Control Unit

f47:Replace Control Unit

Control Unit fault

Change Control Unit

f48:Return Control Unit

Control Unit fault

Change Control Unit

https://harrissupplyind.com - To Order Parts Call 608-268-8080

Содержание iS1100































































Результаты поиска

Содержание iS1100

Отзывы:

Похожие инструкции для iS1100

Бренды по названию

Популярные бренды

Ice iS1100, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание iS1100

Отзывы:

Похожие инструкции для iS1100

Бренды по названию

Популярные бренды