ICC OPC-PRT3 Скачать руководство пользователя страница 6

Страница: 6 / 115

ICC

−

TABLE OF CONTENTS

−

PRE-OPERATION INSTRUCTIONS ............................................................. 8

Product Overview .................................................................................................... 8

1.2

Features and Specifications .................................................................................. 8

1.3

Unpacking and Product Confirmation ................................................................ 13

1.3.1

Shipment Confirmation ..................................................................................................... 13

1.3.2

Component Overview....................................................................................................... 14

1.4

LED Indicators ....................................................................................................... 15

1.4.1

Network Status LED ......................................................................................................... 15

1.4.2

Module Status LED .......................................................................................................... 15

1.4.3

Ethernet Link/Activity LEDs .............................................................................................. 15

INSTALLATION .......................................................................................... 16

2.1

Pre-Installation Instructions ................................................................................. 16

2.2

Installation Procedure for FRENIC-MEGA, FRENIC-HVAC, FRENIC-HVAC-P,

FRENIC-AQUA, non-Ace Inverters ............................................................................... 16

2.3

Installation Procedure for FRENIC-Ace Inverter ................................................ 18

INVERTER FUNCTION CODE SETTINGS ................................................ 23

3.1

Inverter Control-Related Settings ........................................................................ 23

3.2

Inverter Reaction to Network Timeout Conditions ............................................ 24

FUNCTION CODE NUMBERING AND BEHAVIOR ................................... 25

4.1

Register Numbers ................................................................................................. 25

4.2

Scanned Function Codes ..................................................................................... 28

4.3

Commonly Used Function Codes ........................................................................ 29

TIMEOUT PROCESSING ........................................................................... 31

FUJI CONFIGURATION STUDIO ............................................................... 32

6.1

Overview ................................................................................................................ 32

6.2

General Object Editing Activities ........................................................................ 34

6.3

Device Settings ..................................................................................................... 35

6.4

Ethernet Settings .................................................................................................. 35

6.4.1

Authentication .................................................................................................................. 35

6.4.2

Network Configuration...................................................................................................... 35

6.5

Batch Update Mode ............................................................................................... 35

6.6

Internal Logic Settings ......................................................................................... 36

6.6.1

Fail-safe Values ............................................................................................................... 36

6.6.1.1

Overview................................................................................................................... 36

6.6.1.2

Timeout Time ............................................................................................................ 37

6.6.1.3

Timeout Object Configuration ................................................................................... 37

6.6.2

Fail-safe Example ............................................................................................................ 37

6.7

Discovery over Ethernet ....................................................................................... 38

6.7.1

Discovery On Local Ethernet Network .............................................................................. 38

6.7.2

Discovery over the Internet .............................................................................................. 38

6.7.2.1

How to Configure Remote Sites ................................................................................ 39

6.8

Manage Device Parameters .................................................................................. 40

Содержание OPC-PRT3




















































































































Результаты поиска

Содержание OPC-PRT3

Отзывы:

ICC OPC-PRT3, Инструкция по эксплуатации, Страница: 6 / 115

Результаты поиска

Содержание OPC-PRT3

Отзывы: