ICC OPC-PRT3 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 115

ICC OPC-PRT3 Скачать руководство пользователя страница 39

ICC

38

Figure 13: Timeout Object Settings

The example is complete.

6.7

Discovery over Ethernet

6.7.1 Discovery On Local Ethernet Network

Depending on the currently-enabled driver, the Configuration Studio will automatically discover the
device on the Ethernet network,

regardless of whether or not the card’s network settings are compatible

with the subnet upon which they reside. All connected devices are automatically added to the

Discovered Devices

panel. This panel is shown by selecting the

Online Devices

list heading in the

Project

panel. In the

Discovered Devices

panel, discovered Ethernet devices will be listed under

Ethernet

and will display the firmware version in brackets and the current IP address in parentheses to

the right of the device name (refer to Figure 14.)

In order for the studio to discover
devices, certain UDP Ethernet traffic
(port 4334) must be allowed in and
out of the computer, and firewall
applications (such as Windows
Firewall) are often configured to
block such traffic by default. If the
studio is unable to discover any
devices on the current subnet, be sure to check the computer’s firewall settings during troubleshooting,
and add the studio as a program exception to the firewall configuration if necessary. It may be necessary
to restart your PC before the new firewall configuration can take effect.

The network settings of a discovered card
can be configured remotely by:

•

Right-clicking on the device in the

Project

panel and choosing

Configure Network Settings…

from

the context-sensitive menu.

•

Selecting the device in the

Project

panel and navigating to

Device…Configure Network
Settings...

The network settings pop-up should appear
similar to Figure 15. Modify the network
settings as necessary and click the OK
button for the changes to take effect. Note
that this will cause the device to become
temporarily inaccessible and may trip the inverter.

6.7.2 Discovery over the Internet

The studio supports connecting to remote devices over the internet. However, due to internet routing
limitations, the studio cannot automatically discover remote devices in the same manner as on the local
Ethernet network. Therefore, some configuration is required to provide details to the studio on how to
connect to the remote device. This is performed by opening the

Remote Sites

window by navigating to

Discovery…Remote Sites…

.

Figure 14: Configuration Studio Discovery over Ethernet

Figure 15: Remotely Configure Network Settings

«
...
37
38
39
40
41
...
»

Содержание OPC-PRT3




















































































































Отзывы:

Нет отзывов