IBM TS2290, Руководство пользователя

Страница: 122 / 157

Cartridges VOLSER Cartridges VOLSER
Ultrium 9 Data Cartridge xxxxxxL9
Ultrium 9 WORM Cartridge xxxxxxLZ
Ultrium 8 Data Cartridge xxxxxxL8
Ultrium 8 WORM Cartridge xxxxxxLY
LTO M8 Cartridge xxxxxxM8
Ultrium 7 Data Cartridge xxxxxxL7
Ultrium 7 WORM Cartridge xxxxxxLX
Ultrium 6 Data Cartridge xxxxxxL6
Ultrium 6 WORM Cartridge xxxxxxLW
Ultrium 5 Data Cartridge xxxxxxL5
Ultrium 5 WORM Cartridge xxxxxxLV
Ultrium 4 Data Cartridge xxxxxxL4
Ultrium 4 WORM Cartridge xxxxxxLU
Ultrium 3 Data Cartridge xxxxxxL3
Ultrium 3 WORM Cartridge xxxxxxLT
Ultrium 2 Data Cartridge xxxxxxL2
Ultrium 1 Data Cartridge (READ ONLY) xxxxxxL1
LTO Ultrium Cleaning Cartridge CLNxxxLx
*An Ultrium 3 Tape Drive must have a minimum firmware level of 54xx for it to be compatible with the WORM cartridge.
To determine the complete specifications of the bar code and the bar code label, visit the web at http://www.ibm.com/ and enter "IBM LTO Ultrium Cartridge Label
Specification" in the search box. Or contact your IBM sales representative.
When a bar code label is attached to a tape cartridge, place the label only in the recessed label area (see 5 in
LTO media ). A label that extends outside of the recessed
area can cause loading problems in the drive.
Attention: Do not place any type of mark on the white space at either end of the bar code. A mark in this area might prevent the library from reading the label.
Figure 1. Sample bar code label on the LTO Ultrium Tape Cartridge. The volume serial number (LTO123) and bar code are printed on the label.
Guidelines for bar code labels
Apply some basic guidelines when you use bar code labels for your data cartridges.
Guidelines for bar code labels
Edit online
Apply some basic guidelines when you use bar code labels for your data cartridges.
Use only IBM-approved bar code labels on cartridges to be used in an IBM® tape library.
Do not reuse a label or reapply a used label over an existing label.
Before you apply a new label, remove the old label by slowly pulling it at a right angle to the cartridge case.
Use peel-clean labels that do not leave a residue after it is removed. If there is glue residue on the cartridge, remove it by gently rubbing it with your finger. Do not
use a sharp object, water, or a chemical to clean the label area.
Examine the label before it is applied to the cartridge. Do not use the label if it has voids or smears in the printed characters or bar code. A library 's inventory
operation takes much longer if the bar code label is not readable.
Remove the label from the label sheet carefully. Do not stretch the label or cause the edges to curl.
Position the label within the recessed label area (see 5 in
Figure 1 ).
With light finger pressure, smooth the label so that no wrinkles or bubbles exist on its surface.
Verify that the label is smooth and parallel, and has no roll-up or roll-over. The label must be flat to within 0.5 mm (0.02 in.) over the length of the label and have no
folds, missing pieces, or smudges.
Do not place other machine-readable labels on other surfaces of the cartridge. They might interfere with the ability of the drive to load the cartridge.
Write-Protect switch
Edit online
The position of the write-protect switch on the tape cartridge determines whether you can write to the tape.
If the switch ( 1 ) is set to:
The locked position (solid red). Data cannot be written to the tape.
The unlocked position (black void). Data can be written to the tape.
116 IBM TS22xx - TS2290, TS2280, and TS2270