IBM SureMark 4610 1NF страница 100 Скачать руководство пользователя | Manualshive

Страница: 100 / 112

background image

Electronic emission notices

Federal Communications Commission (FCC) statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. IBM is not responsible for any radio or television interference caused by using other than
recommended cables and connectors or by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

European Union EMC Directive conformance statement

This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the
approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot
accept responsibility for any failure to satisfy the protection requirements resulting from a
non-recommended modification of the product, including the fitting of non-IBM option cards.

This product has been tested and found to comply with the limits for Class A Information Technology
Equipment according to CISPR 22/European Standard EN 55022. The limits for Class A equipment were
derived for commercial and industrial environments to provide reasonable protection against interference
with licensed communication equipment.

Attention:

This is a Class A product. In a domestic environment this product may cause radio interference

in which case the user may be required to take adequate measures.

European Community contact:

IBM Technical Regulations
Pascalstr. 100, Stuttgart, Germany 70569
Telephone: 0049 (0)711 785 1176
Fax: 0049 785 1283
E-mail: [email protected]

86

SureMark Hardware Service

«
...
98
99
100
101
102
...
»

Содержание SureMark 4610 1NF

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SureMark 4610 1NF

Бренд: IBM Страницы: 112

Magicolor 2 Desklaser

Бренд: QMS Страницы: 60

Бренд: Oki Страницы: 128

Бренд: Oki Страницы: 189

Бренд: Zebra Страницы: 29

Бренд: StarTech.com Страницы: 13

Бренд: Kimo Страницы: 2

Бренд: MAXPhotonics Страницы: 24

Бренд: Oki Страницы: 309

Designer XL PRO

Бренд: PICASO 3D Страницы: 72

Бренд: Oki Страницы: 105

imagePROGRAF TM-355

Бренд: Canon Страницы: 52

Бренд: Canon Страницы: 769

Бренд: DataCard Страницы: 106

Бренд: Epson Страницы: 157

5700i - EPL B/W Laser Printer

Бренд: Epson Страницы: 33

2180 - LQ B/W Dot-matrix Printer

Бренд: Epson Страницы: 2

2190 - FX B/W Dot-matrix Printer

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды