IBM SureMark 4610 1NF страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 112

background image

24 Vdc connector

Connect the power adapter to the 24 Vdc power connector

G

(Figure 3 on page 7) to provide

power to the printer. This connector should be used only when the 24 V USB communications and
power connector is not used.

Electronic journal card slot

The electronic journal card slot

H

(Figure 3 on page 7) accommodates the electronic journal card

for storing the electronic journal. Depending on country specific regulations, the electronic journal
is either key lock accessible, always accessible, or accessibly by opening the fiscal assembly.

Electronic journal card slot cover

The electronic journal card slot cover

I

(Figure 3 on page 7) is a device that can be used as an

additional fiscal security device to secure the electronic journal card in card slot. The slot cover
can also be used as dust cover, when there is no electronic journal card installed in the slot.

Keylock (optional)

The optional keylock

J

(Figure 3 on page 7) is used to lock the electronic journal card slot cover

in the closed position and secure the installed electronic journal card that contains the electronic
journal.

Note:

An optional internal security screw may be installed to secure the electronic journal card
slot cover in the closed position (see Appendix B, “Country specific information,” on page 77
for more information on this country specific option)

Fiscal tray cover

The fiscal tray cover

K

(Figure 3 on page 7) is secured in place with four screws and provides

an extra layer of fiscal security by providing an additional protection against tampering or disabling
the fiscal logic card.

Service jumper

This jumper is used in the fiscalization operation.

Table 3. Communication interface, rate, and power source

Device

Description

Power

RS-232

115.2 K baud rate

Power-cord and brick

USB

USB is 2.0-Compliant Full-Speed HID; bulk
transfers at 12 Mbps (megabits per second)

System unit input voltage (+24 V);
power-cord and brick if standard USB cable
is used

Power

The IBM SureMark 4610 Model 1NF printers are powered by connecting a power cord and brick to the
power connector or by connecting a 2 meter USB powered signal cable or 4 meter USB powered signal
cable between the system and the 24 V powered USB port on the back of the printer.

Note:

If you are connecting to a system that is not manufactured by IBM. You must connect a power-cord
between the brick and the power-cord connector on the printer.

Using the power-cord and brick

The power-cord and brick are used to supply power to the printer when:

v

The printer is connected to the system using the RS-232 connector.

v

The printer is connected to a standard USB port (for example, on a non-IBM Point of Sale system.) .

Locating the power reset switch

The power reset switch

A

(Figure 4 on page 9) for the 4610 Model 1NF single-station printer is located

under the paper door.

8

SureMark Hardware Service

«
...
20
21
22
23
24
...
»

Содержание SureMark 4610 1NF

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SureMark 4610 1NF

image Prograf iPF785 Series

Бренд: Canon Страницы: 136

Бренд: GBC Страницы: 110

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Бренд: 3DP Страницы: 12

Бренд: Samsung Страницы: 2

Бренд: TallyGenicom Страницы: 175

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 341

Бренд: Samsung Страницы: 8

CLX2160N - Color Laser - All-in-One

Бренд: Samsung Страницы: 118

CLX 3160FN - Color Laser - All-in-One

Бренд: Samsung Страницы: 142

CLP-770ND - Color Laser Printer

Бренд: Samsung Страницы: 2

CLP 610ND - Color Laser Printer

Бренд: Samsung Страницы: 114

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды