IBM RackSwitch G8264T Скачать руководство пользователя

Страница: 28 / 64

RackSwitch G8264T: Installation Guide

Technical specifications

The RackSwitch G8264T technical specifications are described in the following

sections.

Physical characteristics

Physical characteristics of the RackSwitch G8264T switch unit are listed in the

following table.

Environmental specifications

Environmental specifications for the RackSwitch G8264T switch unit are listed in the

following table.

Table 8. RackSwitch G8264T Physical Characteristics

Dimensions (H x W x D)

Weight

4.4 x 43.9 x 51.6 cm.
(1.73 x 17.3 x 20.3 in.)

11.1 kg. (24.5 lb) (maximum)

Table 9. Environmental Specifications

Specification

Measurement

Temperature,

ambient operating

0ºC to +40ºC
(32ºF to 104ºF)

Temperature (fan failure), operating

0ºC to +35ºC
(32ºF to 95ºF)

Temperature, storage

-40ºC to +75ºC
(-40ºF to 167ºF)

Relative humidity

(non-condensing), operating

10 to 90%

Relative humidity

(non-condensing), storage

10 to 90%

Altitude, operating

1,800 m (6,000 feet)

Altitude, storage

12,190 m (40,000 feet)

Acoustic noise

Less than 65dB

Heat dissipation

1331 BTU/hour (typical)
1492 BTU/hour (maximum)

Содержание RackSwitch G8264T

































































Результаты поиска

Содержание RackSwitch G8264T

Отзывы:

Похожие инструкции для RackSwitch G8264T

Бренды по названию

Популярные бренды

IBM RackSwitch G8264T, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264T

Отзывы:

Похожие инструкции для RackSwitch G8264T

Бренды по названию

Популярные бренды