manualshive.com logo in svg

IBM Netfinity 4500R, Руководство по техническому обслуживанию аппаратной части, Страница: 32 / 192

Поделиться
Скачать
IBM Netfinity 4500R Скачать руководство пользователя страница 32

 24

Hardware Maintenance Manual: Netfinity 4500R Type 8656

 

 

UNIX messages

This section provides descriptions of the Ethernet error messages for the SCO UNIX 
LLI driver, and suggested actions to resolve each problem.

PermaNet Server:

Switching back to Primary Adapter. 

Explanation: 

The primary Ethernet connection is now operating correctly. Network traffic 

will automatically transfer to the primary Ethernet controller.

              Action:

 None needed, 

message is for information only.    

Table 5. UNIX LLI driver messages for the Ethernet controller. 

pnt0-2

PCI search specified, PCI device not found!

 

Explanation:

 The driver cannot locate the Ethernet controller on the PCI bus. 

        Action:

 

•

Run the NETCONFIG program to search for another Ethernet controller

•

Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, run the 
diagnostic programs.

pnt0-6

Cannot allocate memory for the adapter during an interrupt. Please check your Streams 
parameters. 

Explanation: 

On a SunSoft Solaris system, this message indicates that the system is out of Streams 

memory blocks. 

                         Action:

 Use the CRASH utility to increase the number of Streams 

memory blocks. Modify the interrupt request (IRQ) settings in the Configuration/Setup Utility 
program, or run the NETCONFIG program to match the hardware settings.

pnt0-7

Cannot allocate memory for the adapter during reset. Please check your Streams parameters. 

Explanation:

 The system is out of Streams memory blocks. 

                                         Action:

 Use the 

CRASH utility to increase the number of Streams memory blocks.

pnt0-11

Device not found!

 

Explanation:

 The driver cannot find an Ethernet controller.

                                     Action:

 Verify that 

the Ethernet controller is enabled. If the Ethernet controller is enabled, run the diagnostic 
programs.

pnt0-12

Device failed checksum test! 

Explanation:

 The driver cannot find an Ethernet controller.

                                     Action:

 Verify that 

the Ethernet controller is enabled. If the Ethernet controller is enabled, run the diagnostic 
programs.

pnt0-13

add_intr_handler failed!  Interrupts already enabled. 

Explanation:

 The interrupt request (IRQ) that was specified, or the IRQ that was found, conflicts 

with other devices in the server. 

Action: 

Modify your hardware settings.

pnt0-14

Cannot locate hardware. 

Explanation:

 The SunSoft Solaris driver cannot find any Ethernet controller. 

           Action:

 Verify 

that the Ethernet controller is enabled. If the Ethernet controller is enabled, run the diagnostic 
programs.

pnt0-15

No more devices to open. 

Explanation:

 The SunSoft Solaris driver cannot find any more Ethernet controllers. 

  Action:

 

Verify that additional IBM Netfinity 10/100 Fault Tolerant Adapters are present or replace the 
Ethernet adapter that fails to respond. If the problem persists, run the diagnostic programs.

Table 4. NDIS (Windows NT) driver messages for the Ethernet controller. 

Содержание Netfinity 4500R

































































































































































































Отзывы:

Нет отзывов