IBM InfoPrint Color 100 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 74

background image

Ventilation

Provide appropriate ventilation to conform to health, safety, and environment standards. The American
Society of Heating, Refrigeration, and Air Conditioning Engineers (ASHREA) recommends a minimum of
34.2 cubic meters per hour (20 cubic feet per minute) per person of outdoor air make-up during human
occupancy.

To comply with the most stringent state Office of Environmental Health Hazard Assessment (OEHHA)
guidelines (California), ensure that the printer area meets the following ventilation requirements:

1. If the printer room has a volume greater than 1 000 m

³

(35 315 f

³

) for each InfoPrint Color 100

installed, a minimum outdoor air exchange of 1 300 m

³

/h (765 f

³

/m) per printer is required. For room

temperatures exceeding 26°C (79°F), the fresh air exchange rate must be increased.

2. If the printer room has a volume smaller than 1 000 m

³

(35 315 f

³

) for each installed InfoPrint Color

100, or if the air exchange rate and temperature requirements cannot be met, you must install a
ventilation system. The ventilation system must provide active local exhaust from the printer to the
outside of the building.

IBM recommends that you locate and install a ventilation system with 6 inch (15.25 cm) tubing to connect
to the exhaust air collector installed by the service representative. Refer to Figure 2 on page 12, or position
3 in Figure 10 on page 19. Exhaust air from three cooling fans at the top of the printer fixed tower and the
fan on the paper supply cover is routed through hoses to an exhaust air collector. Your exhaust system will
attach to this exhaust air collector at the top of the printer. A 6.3 inch (16 cm) diameter, 33 foot (10 m)
length hose is supplied with the air collector to attach to your ventilation system. A fan or blower should be
installed in the exhaust duct to assist in moving printer exhaust air to the outside air. Your exhaust system
must provide a minimum air flow rate of 750 m

³

/h (441 f

³

/m) for each installed InfoPrint Color 100 printer.

Heat Dissipation and Cooling

Table 3. Heating and Cooling Specifications (Approximate)

Description

50–60Hz

Printer with PES Control Unit

Idle

Printing

19.5 kBTU/hr (5.72 kW)

30.0 kBTU/hr (8.79 kW)

Cooling Unit

4.1 kBTU/hr (1.20 kW)

7.8 kBTU/hr (2.29 kW)

Collator

3.4 kBTU/hr (1.00 kW)

3.4 kBTU/hr (1.00 kW)

RIP Controller

0.4 kBTU/hr (0.12 kW)

0.4 kBTU/hr (0.12 kW)

Monitor

0.55 kBTU/hr (0.16 kW)

0.55 kBTU/hr (0.16 kW)

Totals

27.95 kBTU/hr (8.20 kW)

42.15 kBTU/hr (12.4 kW)

Acoustic Levels

The InfoPrint Color 100 acoustic levels do not exceed 71 dB sound pressure and 7.1 bels sound power in
either standby or operating modes.

Lighting

Avoid intensive ultraviolet (UV) sources such as direct sunlight. Fluorescent lighting at normal levels is
permitted. Excessive amounts of UV may cause premature failure of the printer drums.

10

IBM InfoPrint Color 100 Introduction and Planning Guide

«
...
22
23
24
25
26
...
»

Содержание InfoPrint Color 100











































































Отзывы:

Нет отзывов

Похожие инструкции для InfoPrint Color 100

SPP 2020 - Photo Printer - 20 Sheets

Бренд: Samsung Страницы: 81

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 203

Бренд: Samsung Страницы: 264

Бренд: Samsung Страницы: 228

Бренд: Samsung Страницы: 211

Бренд: Samsung Страницы: 5

Бренд: Samsung Страницы: 92

Бренд: Samsung Страницы: 75

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 206

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 103

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 215

Бренд: Samsung Страницы: 2

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 266

550N - CLP Color Laser Printer

Бренд: Samsung Страницы: 296

Бренд: Samsung Страницы: 276

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды