IBM CS821 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 118

background image

The identify LED is at (2). Turn it on by using a system identify command or by pressing the UID button.

Drive LEDs can indicate the following states:

v

Blue activity LED can indicate the following states:
– When there is no activity, the LED is off for SATA drives; on for SAS drives.
– Flashing blue indicates activity

v

Red status LED can indicate the following states. The status LED does not work when SATA drives are
directly attached to the system backplane.
– Steady red indicates that the drive failed
– Flashing red at 4 Hz identifies the drive
– Flashing red at 1 Hz indicates that the drive is rebuilding

Power supply LEDs can indicate the following states:

v

Steady green indicates that power is on

v

Steady amber indicates that power is off, or a power fault occurred

v

Flashing amber indicates that the power supply is overheating

Identifying the 8001-12C, 8001-22C, 8005-12N, or 8005-22N that needs
servicing

Use the Intelligent Platform Management Interface (IPMI) program to turn on the blue identify LED to
help you find the IBM Power System S821LC (8001-12C), the IBM Power System S822LC for Big Data
(8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N) system that needs servicing.

Procedure

Use the

ipmitool

command to activate the blue system identify LED.

For in-band networks, enter the following chassis identify command:

ipmitool -I <interface> chassis identify <interval>

interface

The interface that you are using to connect to the system. For example,

usb

.

interval

The time to turn on the identify LED in seconds. The default value is 15. This means that the LED is
on for 15 seconds and then turns off for 15 seconds. A value of zero (0) turns off the LED. A value of

force

turns on the LED and leaves it on until turned off.

Figure 77. LEDs on the rear of the system

Common procedures for servicing or installing features in the 8001-12C or 8005-12N

69

«
...
83
84
85
86
87
...
»

Содержание CS821























































































































Отзывы:

Нет отзывов

Похожие инструкции для CS821

Бренд: Fagor Страницы: 256

Бренд: SafetySpeed Страницы: 43

Бренд: OCZ Страницы: 8

Бренд: Baileigh Industrial Страницы: 56

Бренд: S.E.F.A Страницы: 26

Бренд: WAGO Страницы: 44

Бренд: Parkside Страницы: 105

Бренд: Uniflex Страницы: 44

Бренд: Sygonix Страницы: 8

Бренд: WERKU Страницы: 40

Бренд: EINHELL Страницы: 34

Бренд: XP Страницы: 42

Бренд: Valcom Страницы: 2

Бренд: BluePoint Fasteners Страницы: 13

Бренд: Crestron Страницы: 8

Electroblock EBL 30

Бренд: Schaudt Страницы: 16

Бренд: Lacme Страницы: 17

Бренд: UUGear Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды