IBM CS821 Скачать руководство пользователя страница 61

Страница: 61 / 118

12.

Place the system backplane on an ESD mat.

Replacing the system backplane in the 8001-12C or 8005-12N

Learn how to replace the system backplane in the IBM Power System S821LC (8001-12C) or the IBM
CS821 (8005-12N) system.

Procedure

Ensure that you have the electrostatic discharge (ESD) wrist strap attached. If not, attach it now.

Remove the replacement system backplane from the static-protective package and place it on an ESD
mat.

The following steps move the system processor module from the old system backplane to the new system
backplane:

Loosen the load arm screw (A) of the system processor heat sink (B) that you are removing with a
#3 Phillips screw driver. The load arm pivots up in the direction that is shown in Figure 51 on page
46.

Figure 50. Lifting out the system backplane

Removing and replacing parts

Содержание CS821























































































































Результаты поиска

Содержание CS821

Отзывы:

Похожие инструкции для CS821

Бренды по названию

Популярные бренды

IBM CS821, Руководство по обслуживанию

Результаты поиска

Содержание CS821

Отзывы:

Похожие инструкции для CS821

Бренды по названию

Популярные бренды