IBM Aptiva 2170 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 252

background image

84

Identifying the Parts of the System Unit

This computer system has four bays that can hold 5.25-inch and 3.5-inch
drives. Additional devices can be installed in the empty bays.

Diskette drives in this unit use the standard diskette advanced technology (AT)
interface. Hard disk drives in this unit use an integrated drive electronics (IDE)
AT interface. This computer supports the American National Standards
Institute (ANSI) standard for AT attachment disk drives.

It also has interface slots for installation of additional cards devices. Industry
Standard Architecture (ISA) and Peripheral Component Interconnect (PCI)
adapter cards are both supported.

1. Bay 1.

This drive bay can hold a 5.25-inch half high drive or a 5.25-inch slim drive.
A 3.5-inch drive can be accommodated with additional brackets. This bay
can hold a CD-ROM, DVD-ROM, diskette, hard disk, tape, or Zip drive.

2. Bay 2.

This drive bay can hold a 5.25-inch half high drive or a 5.25-inch slim drive.
A 3.5-inch drive can be accommodated with additional brackets. This bay
can hold a CD-ROM, DVD-ROM, diskette, hard disk, tape, or Zip drive.

3. Bay 3.

This drive bay can hold a 3.5-inch slim drive, such as a diskette, hard disk,
tape, or Zip drive.

4. Bay 4.

This drive bay is designed for a 3.5-inch diskette drive.

«
...
116
117
118
119
120
...
»

Содержание Aptiva 2170





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aptiva 2170

Бренд: Harbor Freight Tools Страницы: 4

Vehicle-Mount Computer 8515

Бренд: Psion Teklogix Страницы: 190

DESKMINI SERIES

Бренд: ASROCK Страницы: 70

Бренд: Everex Страницы: 47

Бренд: Moxa Technologies Страницы: 27

Бренд: Uplift Desk Страницы: 2

SIMATIC IPC627C

Бренд: Siemens Страницы: 52

Бренд: Siemens Страницы: 32

INOX PRO SIMATIC IPC277D

Бренд: Siemens Страницы: 25

simatic ipc227e

Бренд: Siemens Страницы: 156

SIMATIC Box PC 620

Бренд: Siemens Страницы: 226

Бренд: IEI Technology Страницы: 118

Бренд: Siemens Nixdorf Страницы: 26

Бренд: Fanvil Страницы: 12

Бренд: Fanvil Страницы: 15

Бренд: Fanvil Страницы: 54

Plug PC LXP 2310

Бренд: Chip PC Страницы: 4

Бренд: VonHaus Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды