IBM Aptiva 2170 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 252

background image

76

Diagnostic Diskette

WARNING: This manual is intended to test the IBM Aptiva 2170/2171/2172

machine type only. Testing devices which are not included with the
original product package, including other IBM products, prototype cards,
or modifying hardware settings may give false errors and invalid system
responses. The diagnostics not specifically made for this model may
also report incorrect errors and information.

The diagnostics program comes on a diskette along with this book. This
version of PC-Doctor diagnostics program, developed by Watergate for IBM, is
the primary method of testing the computer. You can use it to test the IB
components of the system and some external devices. The amount of time
required to test components depends on the number of components installed
and selected. The more devices you have attached to your system and
selected in PC-Doctor, the longer the testing will take.

NOTE: The diagnostics program for Aptiva 2170/2171/2172 are the same.

Using the Diagnostic Diskette

1. Power-off the system unit.

2. Insert diagnostic diskette in drive A.

3. Power-on the system unit.

NOTE: Do not press F1 during POST. If any POST errors appear after POST,

make a note of the errors.

4. DOS should load. During boot, verify that each driver loads successfully. For

drivers that do not load successfully, verify that the device driver is
associated with it and is installed properly.

5. Diagnostics program (PC-Doctor) will load, then follow the screen

instructions to operate.

«
...
108
109
110
111
112
...
»

Содержание Aptiva 2170





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aptiva 2170

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 18

Бренд: Acer Страницы: 30

Бренд: Canon Страницы: 160

D-3362-I Series

Бренд: Icop Страницы: 14

Бренд: Radio Shack Страницы: 52

Бренд: Gateway Страницы: 182

Matrix MXC-4000 Series

Бренд: ADLINK Technology Страницы: 80

Compaq Presario,Presario 4103

Бренд: Compaq Страницы: 2

VisuNet GXP PC-GXP1100-22F

Бренд: Pepperl+Fuchs Страницы: 54

Бренд: Gateway Страницы: 2

Бренд: Gateway Страницы: 98

Бренд: Gateway Страницы: 190

WCO-3400 Series

Бренд: Premio Страницы: 60

Бренд: Premio Computer Страницы: 142

Бренд: Datatech Enterprises Страницы: 130

Бренд: FabiaTech Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды