IBM Aptiva 2170 Скачать руководство пользователя страница 80

Страница: 80 / 252

Diskette drive read/write error.

Diskette.

Ensure that the diskette drive is not set to [Write
protect] in the Security Options of BIOS Setup. See
“Security Options” on page 22.

Diskette drive cable.

Diskette drive.

System board.

Diskette drive LED comes on
for more than 2 minutes when
reading data.

Diskette

Diskette drive connection/cable

Diskette drive

System board

Diskette drive LED fails to light,
and the drive is unable to
access for more than 2
minutes.

Diskette

Diskette drive powe

Diskette drive connection/cable

Diskette drive

System board

Diskette drive test failed.

Diskette

Diskette drive

Diskette drive cable

System board

Hard Disk Drive

NOTE:

Ensure hard disk drive is configured correctly in BIOS Setup, cable/jumper are

set correctly before diagnosing any hard disk drive problems.

Hard disk drive test failed.

Enter BIOS Setup and Load default settings.

Hard disk drive cable.

Hard disk drive.

System board.

Hard disk drive format error.

Enter BIOS Setup and Load default settings.

Hard disk drive cable.

Hard disk drive.

System board.

Hard disk drive write error.

Enter BIOS Setup and Load default settings.

Hard disk drive.

Table 2-3 Error Symptoms List

(Continued)

NOTE:

To diagnose a problem, first find the error symptom in the left column. If directed

to a check procedure, replace the FRU indicated in the check procedure. If no
check procedure is indicated, the first Action/FRU listed in right column is the
most likely cause.

Error Symptoms

Action/FRU

Содержание Aptiva 2170





























































































































































































































































Результаты поиска

Содержание Aptiva 2170

Отзывы:

Похожие инструкции для Aptiva 2170

Бренды по названию

Популярные бренды

IBM Aptiva 2170, Руководство по обслуживанию оборудования

Результаты поиска

Содержание Aptiva 2170

Отзывы:

Похожие инструкции для Aptiva 2170

Бренды по названию

Популярные бренды