IBM Aptiva 2124 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 310

background image

2-42

Undetermined Problems

If an error code is present, go to “Index of Symptoms, Messages, Error
Codes, or Beeps” on page 2-8. If no error code is present, continue with this
check. Check the power supply voltages (see "Power Supply Cable
Connector Specifications" on page 5-15). If the voltages are correct, return
here and continue with the following steps:

1. Power off the system unit.

2. Perform the following checks, one by one, until you have isolated the

problem FRU (refer to "Parts/Test Point Locations" on page 5-1 for
locations):

•

Load default settings in setup.

•

Check all system board jumper positions and switch settings.

•

Check all adapter card jumper positions.

•

Check all device jumper positions.

•

Check all cables and connectors for proper installation.

If the jumpers, switch, and voltage settings are correct, return here and
continue:

3. Remove or disconnect the following, one at a time:

•

Non-IBM devices

•

External devices

•

Any

adapters

•

Modem card, if installed

•

CD-ROM

drive

•

Diskette

drive

•

Hard

disk

drive

•

DIMM

•

Processor

•

System

board

4. Power on the system unit.

5. Repeat steps 1 through 4 until you find the failing device or adapter.

6. If software related, reload software from Recovery CD.

«
...
104
105
106
107
108
...
»

Содержание Aptiva 2124























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aptiva 2124

RadioForce GS220

Бренд: Eizo Страницы: 2

Бренд: Collins Страницы: 23

UMEN-260314-V1.0

Бренд: NewHawk Страницы: 14

Бренд: GVision Страницы: 14

Бренд: UltraView Страницы: 36

Бренд: AOC Страницы: 1

Бренд: Yasun Страницы: 19

Бренд: Power View Страницы: 3

NEC MultiSync FE950+ FE950+ FE950+

Бренд: NEC Страницы: 64

LINETRAXX RCMS460-D

Бренд: Bender Страницы: 8

Бренд: weintek Страницы: 8

Бренд: Barco Страницы: 12

Бренд: Emerson Страницы: 5

Бренд: Emerson Страницы: 28

AMS Wireless Vibration Monitor

Бренд: Emerson Страницы: 86

Бренд: Emerson Страницы: 114

Бренд: AOC Страницы: 1

Бренд: FokusLabs Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды