IBM Aptiva 2124 Скачать руководство пользователя страница 45

Страница: 45 / 310

General Information 1-5

Power Supply

•

95 W or 145 W switchable high/low voltage power supply(145 W for 2139
only)

•

Standard ATX power supply with +5V standby power

Internal Cabling

•

Two 40-pin ribbon cables for hard disk drive and CD/DVD-ROM drive.

•

One 34-pin ribbon cable for AT diskette drive.

•

One 4-pin (2-wire) cable for hard disk drive light-emitting diode (LED).

•

One 3-pin (3-wire) cable for power light-emitting diode (LED).

•

One 2-pin (2-wire) cable for power switch.

•

One 4-pin modem voice-in/speaker-out cable.

Modem

•

56.6 Kbps ISA plug and play modem adapter card with data/fax/voice or
voice-less features.

•

Telephone line-out (RJ-11) connector.

•

Telephone line-in (RJ-11) connector.

Monitor

•

Super video graphics array (SVGA) monitor.

•

Compliant to VESA power saving mode.

•

Connector for a detachable grounded 3-wire power cord.

•

1.8-m (5.8-ft) attached signal cable.

•

Auto-sensing power input for 100 Vac to 240 Vac.

•

15” (13.6” viewable image size) monitor

−

0.28-mm dot pitch

−

Automatic scanning horizontal frequencies from 30KHz to 54KHz
and all vertical frequencies between 50Hz and 120Hz.

−

DDC2A/B support

•

15” (13.7” viewable image size) monitor

−

0.28-mm dot pitch

Содержание Aptiva 2124























































































































































































































































































































Результаты поиска

Содержание Aptiva 2124

Отзывы:

Похожие инструкции для Aptiva 2124

Бренды по названию

Популярные бренды

IBM Aptiva 2124, Техническое обслуживание оборудования

Результаты поиска

Содержание Aptiva 2124

Отзывы:

Похожие инструкции для Aptiva 2124

Бренды по названию

Популярные бренды